- 您現在的位置：買賣IC網 > PDF目錄366878 > CPCI-75SD1-08HPF6-XX Converter PDF資料下載
參數資料
| 型號： | CPCI-75SD1-08HPF6-XX |
| 英文描述： | Converter |
| 中文描述： | 轉換器 |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 44K |
| 代理商： | CPCI-75SD1-08HPF6-XX |
Apex Signal,
A Division of NAI, Inc.
631.567.1100/631.567.1823(fax) 1-17-01 s 75 SD1 A001 REV 1.4
170 Wilbur Place, Bohemia, NY, 11716,USA
www.naii.com
/ e-mail:sales@naii.com Code:OVGU1 Page 1 of 4
APEX Signal, A Division of NAI, Inc
.
cPCI-75SD1
cPCI
EIGHT (8) SYNCHRO/RESOLVER-to-DIGITAL
TWO-SPEED OR SINGLE SPEED OR COMBINATIONS (PROGRAMMABLE)
MULTI-SPEED RATIOS: 2 to 255; OPTIONAL INTERNAL REFERENCE
ACCURATE VELOCITY OUTPUTS, CONTINUOUS SELF TEST
TO COMMERCIAL OR MILITARY SPECIFICATIONS
16 bit resolution (24 bit combined)
1 arc minute accuracy
Continuous background bit testing with Reference and Signal loss detection
Power-On Self-Test (POST)
S/D channels are self-calibrating
50 Hz to 10 kHz
Encoder (A & B) plus Index outputs; Programmable resolution
Equivalent A, B, & C Hall Effect commutation outputs
Synchro/Resolver programmable
Transformer isolated
Accurate Digital Velocity outputs
Latch feature
Synthetic reference compensates for
±
60
°
phase shift
I/O via front panel, J2 or both
2,4,or 8 channels available
Commercial or severe environment MIL
DESCRIPTION:
This single slot card contains
eight separate transformer isolated Synchro/Resolver-to-Digital tracking
converters, optional 5 VA reference, and extensive diagnostics.
The (8) measurement channels also produce
differential incremental encoder (A&B) outputs
(with programmable resolution) and a zero degree marker pulse or
Commutation outputs for 4, 6, or 8 pole brushless DC motors that eliminate the need for Hall Effect sensors on the
motor thus eliminating processor time and reducing bus traffic.
The S/R/D channels incorporate high linearity digital
velocity outputs, angle change alert and can be field configured for either single speed or multi-speed to any ratio
between 2 and 255.
Ambiguity circuits maintain monotonic outputs by compensating for misalignment between the
Coarse and Fine Synchros, however, the processor will set a flag when it senses that the max. allowable misalignment
of 90
°
/gear ratio is exceeded. The S/R/D channels, even when large accelerations are encountered, never looses
tracking, because they incorporate the unique capability to automatically shift to higher bandwidths. The shifting is
smooth and continuous with no glitches. Tracking rates are only limited to bandwidth restrictions, up to 150 RPS, at 16
bit resolution. The “Latch” feature permits the user to read all channels at the same time. Reading will unlatch the
channel. The use of Type II servo loop processing techniques enables tracking, at full accuracy, up to the specified
rate. A step input will not cause any hang-up condition. Intermediate transparent latches, assure that current valid data
is always available for any channel without effecting the tracking performance of the converters. Each channel can be
specified for a different voltage,frequency or resolution.
To simplify logistics, Part number, S/N, Date code, & Rev. are located in permanent memory locations.
相關PDF資料 |
PDF描述 |
|---|---|
| CPCI-75SD1-08HPP1-XX | Converter |
| CPCI-75SD1-08HPP2-XX | Converter |
| CPCI-75SD1-08HPP3-XX | Converter |
| CPCI-75SD1-08HPP4-XX | Converter |
| CPCI-75SD1-08HPP5-XX | Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPCI-75SD1-08HPP1-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
| CPCI-75SD1-08HPP2-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
| CPCI-75SD1-08HPP3-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
| CPCI-75SD1-08HPP4-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
| CPCI-75SD1-08HPP5-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
發布緊急采購，3分鐘左右您將得到回復。