欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CPW256-1530-16AA95
元件分類: 插座
英文描述: BGA256, IC SOCKET
封裝: ROHS COMPLIANT
文件頁數: 6/8頁
文件大小: 1199K
代理商: CPW256-1530-16AA95
Socket Mounting Recommendations and Reflow Profile
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland
Phone +41-21-781 08 10 www.e-tec.com info@e-tec.com
E-tec Socket Mounting Recommendations
PRELIMINARY
4
Verifying the Assembly
After the socket has been reflowed to the PCB, open and short testing should be partaken to
ensure proper assembly. The assembly house typically performs x-ray inspection to verify non-
shorting of pins. However, as this is only a visual inspection, we recommend using a continuity
tester or ohmmeter and simply sweeping random rows and columns of pins to ensure no shorting
of pins. No damage to the springs will occur if very slight pressure from the meter’s tips is
applied (just touch the probes to the springs). For fine pitch sockets, a microscope would be
helpful in placing the meter’s tips appropriately.
After verifying the absence of shorts, open testing should be performed. The most direct, yet
tedious, method is to use the continuity tester to directly probe each pin to a breakout or test
point on the board. Again no damage will occur if the probes are touched to the springs. If heavy
pressure is required to push the socket body towards the PCB to achieve continuity, this means a
poor solder joint. If no such test points exist, then the BGA’s via field on the backside of the
PCB should be kept solder-mask free to allow for such probing. If the via field is kept open, a
simpler open testing method can be performed. Simply use a wet sponge (or some other
conductive material) and hold it onto the via field. This shorts all the pins together on the PCB.
Insert one probe of the continuity tester into the sponge. Now sweep the pins of the socket with
the other probe and check for continuity.
If the above procedures show any shorts or opens, then it is advisable to have the assembly house
re-evaluate the assembly method used. An incorrect stencil can lead to too much or too little
solder paste, easily leading short or open conditions and a solder paste with Ag contents
(>=0.5%) may also result in solder joint failures. These are the primary reasons for socket
mounting failures.
Important Notes:
a) Screw/Twist Lock Socket
When tightening the lid of a Screw or Twist Lock socket, it is imperative to not over-tighten the
retention screws, otherwise irreparable damage may occur. Such damage is not covered by
warranty and will be solely the end user’s responsibility. The maximum allowed torque on these
retention screws is 7cN-m (10oz-in) for sockets up to 800 pins and for sockets as of 800 pins the
torque value needs to be increased but should not exceed a maximum of 10cN-m (14oz-in). E-tec
sells the torque screwdriver TOL-7CN-TORQUE which is preset to 7cN-m, but which can be
adjusted to higher torque values for the high pin count sockets.
相關PDF資料
PDF描述
CPW256-1570-16AA95 BGA256, IC SOCKET
CPW484-0528-26AB95L BGA484, IC SOCKET
CCW180-0629-14CB95 BGA180, IC SOCKET
CS068-01TT3M PGA68, IC SOCKET
CCW1152-1570-34AB95 BGA1152, IC SOCKET
相關代理商/技術參數
參數描述
CPW256A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET POWER MODULE | FULL BRIDGE | 500V V(BR)DSS | 17.5A I(D)
CPW256K 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC
CPW256P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET POWER MODULE | INDEPENDENT | 500V V(BR)DSS | 14A I(D)
CPW2870B10-47 制造商:CPI 制造商全稱:CPI 功能描述:COMPACT SERIES DC SPUTTERING POWER SUPPLY WITH INTEGRATED ACTIVE ARC SUPPRESSIO
CPW2870B15 制造商:CPI 制造商全稱:CPI 功能描述:DC SPUTTERING POWER SUPPLY WITH ACTIVE ARC SUPPRESSION
主站蜘蛛池模板: 元谋县| 富平县| 伊宁县| 安阳市| 正定县| 都匀市| 巴彦县| 嵩明县| 遂平县| 公安县| 赤城县| 五家渠市| 江北区| 肥西县| 禄劝| 梅州市| 永年县| 通城县| 榆林市| 肥西县| 廉江市| 咸阳市| 鱼台县| 天全县| 嘉义市| 吴忠市| 中宁县| 页游| SHOW| 堆龙德庆县| 稻城县| 错那县| 黔西县| 阳信县| 和静县| 梁平县| 将乐县| 满城县| 冕宁县| 怀安县| 民县|