- 您現在的位置：買賣IC網 > PDF目錄257682 > CQ1001-7R (POWER-ONE INC) 1-OUTPUT 82 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CQ1001-7R |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 82 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE Q01, MODULE |
| 文件頁數： | 6/25頁 |
| 文件大小： | 747K |
| 代理商： | CQ1001-7R |
Cassette Style
DC-DC Converters
Q Series
Edition 5/5.2000
14/25
Auxilary Functions
i Inhibit for Remote On and Off
Note: If this function is not actively used, the inhibit pin 28
must be interconnected with the negative input pin 32 to en-
able the output(s). A non-connected pin 28 will be inter-
preted by the internal logic as an active inhibit signal and
therefore output(s) will remain disabled: Fail safe function.
An inhibit input enables (logic low, pull down) or disables
(logic high, pull up) the output if a logic signal e.g. TTL,
CMOS is applied. In systems consisting of several units,
this feature may be used, for example, to control the activa-
tion sequence of the converters by means of logic signals,
or to allow the unit's source for a proper start up before full
load is applied (e.g. in combination with LT units).
Table 6: Inhibit characteristics
Characteristics
Conditions
min typ max
Unit
Uinh Inhibit
Uo = on Ui min...Ui max
–100
0.8
V DC
voltage
Uo = off
TC min...TC max
2.4
100
Iinh
Inhibit current
Uinh = –50 V
–500
A
Uinh =0 V
–40
Uinh = 50 V
+500
Uinh = 100 V
+1000
i
Vi–
Vi+
Vo–
S–
Ui
Io
Uo
RL
Ii
Iinh
Uinh
Vo–
Vo+
S+
28
30
32
26
14
10
8
6
4
12
06091
Fig. 18
Definition of input and output parameters
0
tr
Ui
t
0.8
on
off
Uinh [V]
2.4
0.1
Uo/Uo normal
tf
td on
0.99
1.01
06092
Fig. 19
Output response as a function of input voltage (on/off
switching) or inhibit control
Output Response
The output response when enabling and disabling the out-
put by the inhibit input is shown in the following figure.
Table 7: Output response time with outputs resistively loaded and R-input and P option not used
BQ, CQ, GQ
DQ, EQ
Characteristics
Conditions
min
typ
max
min
typ
max
Unit
td on
Turn-on delay time
Ui = 0 → Ui min, RL = Uo nom/0.5 Io nom
5
850
ms
Ui = 0 → Ui nom, RL = Uo nom/Io nom
3.5
250
tr
Output voltage rise time
Ui = 0 → Ui nom, RL = Uo nom/Io nom
2.5
Ui inh = 2.4 → 0.8 V, RL = Uo nom/Io nom
tf
Output voltage fall time
Ui = Ui nom → 0, RL = Uo nom/Io nom
33
Ui inh = 0.8 → 2.4 V, RL = Uo nom /Io nom
Current Sharing (T Function)
The current sharing facility should be used where several
units are to be operated in parallel for high reliability n+1
redundant systems or in order to provide higher output
powers. Using this feature reduces the stress on the units
and further improves the reliability of the system.
Interconnection of the current sharing terminals T causes
the units to share the output current to the average of all
units. The current tolerance of each unit is approx.
±20% of
the sum of its nominal output currents
Io1 nom + Io2 nom.
In n+1 redundant systems, a failure of a single unit will not
lead to a system failure if the outputs are decoupled by di-
odes. See also
Sense Lines.
Since the voltage on the T pin is referenced to the sense pin
S–, the installer must ensure that the S– pins of all units are
at the same electrical potential, i.e. voltage drops
>50 mV
across the connection lines between these pins shall be
avoided.
BQ...GQ 2000 DC-DC converters with outputs connected
in series can also be paralleled with current sharing, if pins
Vo1– of all units are connected together. See
Sense Lines.
If the output voltages are programmed to a voltage other
than
Uo nom by means of the R pin or option P, the outputs
should be adjusted individually within a tolerance of
±1%.
The current sharing will be less accurate when operating
with dynamic loads.
Important: For applications using the hot plug-in capa-
bilities, dynamic output voltage changes during the plug-
in/plug-out cycles must be considered.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1026SE-45TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| CAT1026RD2I-45 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO8 |
| CAT1027PE-25 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1027UI-30 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT1027YI-30 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CQ1001-9R | 功能描述:EURO-CASSETTE 82W 5.1V RoHS:否 類別:電源 - 外部/內部（非板載） >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流（最大）:24 VDC @ 50A 輸出 - 2 @ 電流（最大）:- 輸出 - 3 @ 電流（最大）:- 輸出 - 4 @ 電流（最大）:- 功率（瓦特）:1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包裝:散裝 電源（瓦特）- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH |
| CQ1001-9RG | 功能描述:DC/DC CONVERT 5.1V 20A 制造商:bel power solutions 系列:* 零件狀態:有效 標準包裝:5 |
| CQ10663001 | 功能描述:CABLE STRANDED 制造商:te connectivity raychem cable protection 系列:* 零件狀態:有效 標準包裝:1 |
| CQ10A1KB394K3 | 制造商:ARIZONA 功能描述:CAPACITOR MILITARY FILM 制造商:DEARBORN ELECTRONICS INC 功能描述:CAPACITOR MILITARY FILM |
| CQ10A1KC224K3 | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。