- 您現在的位置：買賣IC網 > PDF目錄257669 > CS1001-9RD2T (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CS1001-9RD2T |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE S02, MODULE |
| 文件頁數： | 20/33頁 |
| 文件大小： | 438K |
| 代理商： | CS1001-9RD2T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 27 of 33
www.power-one.com
NPN output (D5 - DD):
Pin 20 (D) is internally connected via the collector-emitter
path of an NPN transistor to Vo1+ or Vo+. VD < 0.4 V
(logic low) corresponds to a monitored voltage level (Vi
and/or Vo1) > Vt +Vh. The current ID through pin 20
should not exceed 20 mA. This output is not protected
against external overvoltages. VD should not exceed 40 V.
Vi, Vo1 status
D output,
VD
Vi or Vo1 < Vt
high, H,
ID ≤ 25 A at VD = 40 V
Vi and Vo1 > Vt + Vh
low, L,
VD ≤ 0.4 V at ID = 20 mA
JFET output (D0 - D4):
Pin 20 (D) is internally connected via the drain-source path
of a JFET (self-conducting type) to Vo1+ or Vo+.
VD ≤ 0.4 V (logic low) corresponds to a monitored voltage
level (Vi and/or Vo1) < Vt. The current ID through the JFET
should not exceed 2.5 mA. The JFET is protected by a
0.5 W Zener diode of 8.2 V against external overvoltages.
Vi, Vo1 status
D output,
VD
Vi or Vo1 < Vt
low, L,
VD ≤ 0.4 V at ID = 2.5 mA
Vi and Vo1 > Vt + Vh
high, H,
ID ≤ 25 A at VD = 5.25 V
Fig. 31
Option D1 - D0: JFET output, ID ≤ 2.5 mA
Table 21: D-output logic signals
Version of D
Vi << Vt resp. Vo << Vt
Vi >> Vt + Vh resp. Vo >> Vt
Configuration
D1, D2, D3, D4, D0
low
high
JFET
D5, D6, D7, D8, D9, DD
high
low
NPN
Vo1+
Vo1–
D
VD
ID
Rp
Input
11007
Vo1+
Vo1–
D
VD
ID
Rp
Input
11006
Fig. 32
Option D5 - DD: NPN output, Vo1 ≤ 40 V, ID ≤ 20 mA
Threshold tolerances and hysteresis:
If Vi is monitored, the internal input voltage after the input
filter is measured. Consequently, this voltage differs from
the voltage at the connector pins by the voltage drop
ΔVti
across the input filter. The threshold levels of the D0 and
D9 options are factory-adjusted at nominal output current
Io nom and at TA = 25 °C. The value of ΔVti depends upon
the input voltage range (CS, DS, ..), threshold level Vt,
temperature and input current. The input current is a
function of the input voltage and the output power.
Fig. 33
Definition of Vti, ΔVt i and ΔVhi (JFET output)
ΔV
ti
Vhi
VD low
VD
VD high
Vi
P
o
=
P
o
nom
P
o
=
0
P
o
=
0
Vti
P
o
=
P
o
nom
11021
相關PDF資料 |
PDF描述 |
|---|---|
| CS1001-9RD9B1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1301-7EPD7B1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1301-7PD2T | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1301-7PDDT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1301-9ERD3TB1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS-100-206 | 制造商:Benign Industries 功能描述:1/4IN. IN-LINE VALVE |
| CS-100-210 | 制造商:Benign Industries 功能描述:1/4IN. NPT MALE |
| CS-100-223 | 制造商:Benign Industries 功能描述:ASSEMBLY PLIERS - 1/4IN. |
| CS-100-255 | 制造商:Benign Industries 功能描述:STARTER KIT 1/2IN. BORE |
| CS-100-257 | 制造商:Benign Industries 功能描述:HOSE PACK 1/2IN. BORE |
發布緊急采購，3分鐘左右您將得到回復。