- 您現在的位置：買賣IC網 > PDF目錄257669 > CS1601-7EPD2T (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CS1601-7EPD2T |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE S02, MODULE |
| 文件頁數： | 18/33頁 |
| 文件大小： | 438K |
| 代理商： | CS1601-7EPD2T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 25 of 33
www.power-one.com
Load
1
2
S+
Vo+
Vo–
S–
Vi+
Vi–
T
Vi+
Vi–
S+
Vo+
Vo–
S–
T
1
Max. 5 converters in parallel connection
11036_012006
Converter
Fig. 29
Paralleling of single-output models using option T with the
sense lines connected at the load
1 Leads should have equal length and cross sections and should
run in the same cable loom.
2 Diodes for redundant operation.
Vo+
Vo–
Vo+
Vo–
Load
Vo+
Vo–
11003_102005
Fig. 28
An example of poor wiring for connections in parallel
(unequal length of load lines)
Option T: Current Sharing
This option ensures that the output currents are
approximately shared between all paralleled converters,
hence increasing system reliability. To use this facility,
simply interconnect the T pins of all converters and make
sure that the reference pins for the T-pin (S- for the S1000
or Vo1– for S2000) are also connected together. The load
lines should have equal length and cross section to ensure
equal voltage drops. Not more than 5 converters should be
connected in parallel. The R-pins should be left in an open-
circuit condition. If not, prior to paralleling the Vo1 outputs
should be individually adjusted within 1 to 2%. Parallel
connection
of
converters
with
option
P
is
not
recommended.
Option P: Potentiometer
The potentiometer allows for an output voltage adjustment
in the range of +10/–60% of Vo nom. It is accessible
through a hole in the front cover. This feature enables
compensation of voltage drops across the connector and
wiring. Option P is not recommended if models are
connected in parallel.
In double-output models both outputs are influenced by the
potentiometer setting. If option P is fitted, the R-pin 16 is
not connected.
Note: If the output voltage is increased above Vo nom via the
R-input control, option P setting, remote sensing, or option T,
the output current(s) should be reduced accordingly so that
Po nom is not exceeded.
Load
Max. 5 converters in parallel connection
+–
Power bus
Vo2–
Vo2+
Vo1–
Vo1+
T
Vo2–
Vo2+
Vo1–
Vo1+
T
Converter
11037_012006
Fig. 30
Paralleling of double output models with the outputs
connected in series, and using option T in an application
with a power bus. Note that the signal at the T-pins is
referenced to Vo1-.
相關PDF資料 |
PDF描述 |
|---|---|
| CS1601-7PD7B1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1601-7RD0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1601-7RD0TB1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1601-9PDDT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| CS1601-9RD2B1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS1601-7R | 功能描述:EURO-CASSETTE 100W 24V RoHS:否 類別:電源 - 外部/內部（非板載） >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流（最大）:24 VDC @ 50A 輸出 - 2 @ 電流（最大）:- 輸出 - 3 @ 電流（最大）:- 輸出 - 4 @ 電流（最大）:- 功率（瓦特）:1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包裝:散裝 電源（瓦特）- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH |
| CS1601-9ER | 制造商:Power-One 功能描述:DCDC - Bulk |
| CS1601AM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS1601-FSZ | 功能描述:功率因數校正 IC PFC CONTROLLER DCM RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| CS1601-FSZR | 制造商:Cirrus Logic 功能描述:IC PFC CONTROLLER DCM OCP (FOR LIGHTING) - Tape and Reel 制造商:Cirrus Logic 功能描述:IC PFC CTRLR BALLAST 8SOIC 制造商:Cirrus Logic 功能描述:PFC Controller |
發布緊急采購，3分鐘左右您將得到回復。