- 您現在的位置：買賣IC網 > PDF目錄257680 > CS2660-9RD9TB2 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CS2660-9RD9TB2 |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE S02, MODULE |
| 文件頁數： | 6/31頁 |
| 文件大?。?/td> | 633K |
| 代理商： | CS2660-9RD9TB2 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Cassette Style
100 Watt DC-DC Converters
S Series
Edition 1/01.2000
14/31
Table 5: Inhibit data
Characteristics
Conditions
min
typ
max
Unit
Uinh
Inhibit input voltage to keep
Uo = on
Ui min...Ui max
–50
0.8
V DC
output voltage
Uo = off
TC min...TC max
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
t r
Rise time
30
ms
tf
Fall time
depending on
Io
Fig. 15
Typical output response as a function of inhibit control
0
t
0
Inhibit
1
0.1
Uo nom
Output
tr
tf
05073
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should en-
sure that
Uo max (between Vo1+ and Vo1–) is not exceeded.
We recommend connecting the sense lines directly at the
female connector.
For further information, please refer to:
Application Notes.
To ensure correct operation, both sense lines (S+ and S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–)and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Note: The output terminals Vo1+ and Vo1- must always be
connected to the load before connecting the sense lines S+
and S–, otherwise the unit will be damaged.
Table 6: Maximum Voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12 V, 15 V
< 1.0 V
< 0.25 V
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input: Output is disabled (
Uo = off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1–). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail
safe). For output response refer to:
Hold-up Time and Out-
put Response.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Uinh
06031
1.6
0.8
0
–0.8
–50
Uinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Uinh = 0.8 V
Uo = on
Uo = off
Uinh = 2.4 V
06032
Fig. 13
Definition of Uinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Uinh
相關PDF資料 |
PDF描述 |
|---|---|
| CAT810JSDI-T3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT808NTBI-31-GT1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| CAT808NTBI-31-T3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| CAT1024YI-30-GT3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| CTDD2210S-1515S-2 | 1-OUTPUT 2 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS2662BA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS2679-000 | 制造商:TE Connectivity 功能描述:7817A1032-0 |
| CS2681-000 | 制造商:TE Connectivity 功能描述:55PC1111-22-9-9-L016 - Cable Rools/Shrink Tubing |
| CS2704-000 | 制造商:TE Connectivity 功能描述:HRHF-125FR-6/97-CS8413 - Bulk |
| CS-270-K | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use |
發布緊急采購，3分鐘左右您將得到回復。