- 您現在的位置：買賣IC網 > PDF目錄376633 > DEMO9S08RG60UM DEMO9S08RG60 Demonstration Board Users Manual PDF資料下載
參數資料
| 型號： | DEMO9S08RG60UM |
| 英文描述： | DEMO9S08RG60 Demonstration Board Users Manual |
| 中文描述： | DEMO9S08RG60演示板用戶手冊 |
| 文件頁數： | 10/19頁 |
| 文件大小： | 167K |
| 代理商： | DEMO9S08RG60UM |
D E M O 9 0 8 R G 6 0
A U G U S T 6 , 2 0 0 4
10
Figure 1: TB1 Terminal Block Connector
PWR_S EL J umper
The PWR_SEL jumper selects the source of power input to the module, or provides+5VDC to
J1 for use by external circuits. The module takes voltage input from the 2-position on-board
voltage regulator or from the 40-pin MCU connector (J1). Power input at the terminal block
must be DC voltage between +7VDC and +16VDC. Power input on the MCU connector
must
be
regulated voltage between +4.75VDC and +5.25VDC. The MCU_PORT connector power
input allows use of batteries, or other alternate sources, to power the module.
CAUTION:
Module damage may occur if the MCU_PORT power input pins (J1-
1, J1-3) are over-driven.
The PWR_SEL option jumper provides 3 possible configurations; source power from the PWR
connector, source power from J1, or source power from PWR and supply power to J1. The
figure below shows the settings for each configuration.
Figure 2: PWR_SEL Jumper Settings
1
2
Module powered from external input connected to J1-1 (+) and
J1-3 (-). +5VDC Maximum input voltage.
1
2
Module powered from external +6VDC - +16VDC connected to
TB1 Terminal Block. J1-1 is open or not connected.
1
2
Module powered from external +6VDC - +16VDC connected to
TB1 Terminal Block. Module provides +5VDC output at pin J1
for use by external circuits.
NOTE:
Power output from the module is limited by the 250 mA maximum out-
put of the on-board voltage regulator.
NOTE:
External circuit connected to J1 should limit current flow to less than
50 mA to prevent current-limiting the power supply (VR1).
+6VDC -
+16VDC
GND
2 Position, Screw-
Type Terminal Block
MCU_PORT
J1
+
相關PDF資料 |
PDF描述 |
|---|---|
| DEMO9S12NE64QSG | DEMO9S12NE64 Demo Quick Start Guide |
| DEMO9S12NE64UM | DEMO9S12NE64 User＇s Manual |
| DER10A | Accessories Shunts for DC Currents |
| DESC29-06AC | HiPerFRED Epitaxial Diode ISOPLUS220 Electrically Isolated Back Surface |
| DESI60 | Fast Recovery Epitaxial Diode (FRED) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO9S08SC4 | 功能描述:開發板和工具包 - S08 / S12 DEMO BRD FOR 9S08SC4 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S08SE8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR SE8 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S08SE8 | 制造商:Freescale Semiconductor 功能描述:MC9S08SE8 Demonstration board |
| DEMO9S08SF4 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR S08SF4 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S08SG32 | 功能描述:開發板和工具包 - S08 / S12 SG32 DEMO BOARD RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
發布緊急采購，3分鐘左右您將得到回復。