- 您現在的位置：買賣IC網 > PDF目錄376633 > DEMO9S12NE64UM DEMO9S12NE64 User＇s Manual PDF資料下載
參數資料
| 型號： | DEMO9S12NE64UM |
| 英文描述： | DEMO9S12NE64 User＇s Manual |
| 中文描述： | DEMO9S12NE64用戶手冊 |
| 文件頁數： | 7/19頁 |
| 文件大小： | 167K |
| 代理商： | DEMO9S12NE64UM |
D E M O 9 0 8 R G 6 0
A U G U S T 6 , 2 0 0 4
7
3. Set module options for RUN Mode:
VTST_EN
MON_EN
COM_EN
RUN/LOAD
USER_EN
Off / open / idle
Off/ open / idle
2-3 (COM position)
Set to RUN
Enabled as needed for application operation
4. Power On the Module. Application will begin to execute.
MON08 DEBUG MODE on COM
MON08 Monitor Mode operates the HC08 internal MON08 debug monitor from Power-On.
This mode is accessible by setting Module options or by applying a supporting development
cable to the Debug Port. For Debug cable application, the state of the MON_EN option jump-
ers is DON’T CARE. The COM_EN option jumper should be set to the 2-3 position. The
VTST_EN jumper may be required. Refer to the MON08 Configuration section of this docu-
ment for further details. The following settings configure the DEMO908GZ60 module for
MON08 Debug Mode on COM:
1. Configure PWR_SEL option for input supply to power the module. If supply is via J1 con-
nection, install module on J1 external connection in powered down condition. Note that the
VTST_EN option requires 9VDC minimum applied at TB1 to function correctly.
2. Connect one end of the supplied 9-pin serial cable to a free COM port on the PC. Connect
the other end of the cable to the COM port connector on the DEMO908GZ60 module.
3. Install and launch the PC Hosting software for the MON08 communication interface. This
may be a C compiler with IDE and MON08 communication or another MON08 debug host-
ing type software.
4. Set the Module options for MON08 Debug Mode:
VTST_EN
ON / Installed on both pins (required if the Reset
vector is not erased in the flash memory)
ON / Installed on both pins
1-2 (DEBUG position)
Enabled as needed for application operation
MON_EN
COM_EN
USER_EN
5. Apply +9VDC minimum power to the module. This may be applied by TB1 or through J1.
6. Hosting development software will establish MON08 communication now.
相關PDF資料 |
PDF描述 |
|---|---|
| DER10A | Accessories Shunts for DC Currents |
| DESC29-06AC | HiPerFRED Epitaxial Diode ISOPLUS220 Electrically Isolated Back Surface |
| DESI60 | Fast Recovery Epitaxial Diode (FRED) |
| DF005M | MINIATURE GLASS PASSIVATED SINGLE - PHASE - RECTIFIER |
| DF01M | MINIATURE GLASS PASSIVATED SINGLE - PHASE - BRIDGE RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO9S12PFAME | 功能描述:開發板和工具包 - S08 / S12 S12P Demo Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S12XDT512 | 功能描述:開發板和工具包 - S08 / S12 9S12XDP512 DEMO BOARD RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S12XDT512E | 功能描述:開發板和工具包 - S08 / S12 9S12XDP512 DEMO BOARD RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S12XEP100 | 功能描述:開發板和工具包 - S08 / S12 BASIC (SMALL) EVB FOR 9S RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9S12XEP100 | 制造商:Freescale Semiconductor 功能描述:BASIC (SMALL) EVB FOR 9S |
發布緊急采購，3分鐘左右您將得到回復。