- 您現在的位置：買賣IC網 > PDF目錄376741 > DLP-USB1 (Electronic Theatre Controls, Inc.) USB to FIFO Parallel Interface Module PDF資料下載
參數資料
| 型號： | DLP-USB1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | USB to FIFO Parallel Interface Module |
| 中文描述： | USB轉先進先出并行接口模塊 |
| 文件頁數： | 1/6頁 |
| 文件大小： | 67K |
| 代理商： | DLP-USB1 |
Revision 1.4
- 1 -
DLP Design
DLP-USB1
USB to FIFO Parallel Interface Module
DLP-USB1 FEATURES
Send / Receive Data over USB at up to 1 M Bytes / sec
384 byte FIFO Transmit buffer / 128 byte FIFO receive
buffer for high data throughput
Simple interface to CPU or MCU bus
No in-depth knowledge of USB required as all USB
Protocol is handled automatically within the module
FTDI’s Virtual COM port drivers eliminate the need for
USB driver development in most cases.
Integrated 3.3v Regulator – No External Regulator Required
4.4v - 5.25v Single Supply taken directly from the USB port
UHCI / OHCI Compliant
USB 1.1 Specification Compliant
USB VID, PID, Serial Number and Product Description
Strings stored in on-board EEPROM.
Virtual COM Port Drivers for Windows 98, Windows 98 SE,
Windows 2000, Windows Millennium, Apple iMAC and Linux
Application Areas
Prototype Development
USB ISDN and ADSL Modems
High Speed USB PDA Interface
USB Interface for Digital Cameras
USB Interface for MP3 players
High Speed USB Instrumentation
GENERAL DESCRIPTION
The DLP-USB1 provides an easy cost-effective method of transferring data to / from a peripheral and a host at up to
8 Million bits ( 1 Megabyte ) per second. It’s simple FIFO-like design makes it easy to interface to any
microcontroller or microprocessor via IO ports.
To send data from the peripheral to the host computer simply write the byte wide data into the module when TXE#
is low. If the ( 384 byte ) transmit buffer fills up or is busy storing the previously written byte, the device takes
TXE# high in order to stop further data from being written until some of the FIFO data has been transferred over
USB to the host.
When the host sends data to the peripheral over USB, the device will take RXF# low to let the peripheral know that
data is available. The peripheral then reads the data until RXF# goes high indicating no more data is available to
read.
By using FTDI’s virtual COM Port drivers, the peripheral looks like a standard COM Port to the application
software. Commands to set the baud rate are ignored – the device always transfers data at it’s fastest rate regardless
of the application’s baud rate setting.
相關PDF資料 |
PDF描述 |
|---|---|
| DLR5735 | 17.5 mm Single Character 5x7 Dot Matrix Alphanumeric Display |
| DLR5736 | 17.5 mm Single Character 5x7 Dot Matrix Alphanumeric Display |
| DLG5735 | 17.5 mm Single Character 5x7 Dot Matrix Alphanumeric Display |
| DLG5736 | 17.5 mm Single Character 5x7 Dot Matrix Alphanumeric Display |
| DLS8100 | VDSL Wireline Simulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DLP-USB1232H | 功能描述:界面模塊 H-Spd FT2232H Sngle- Chnl USB-UART/FIFO RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-USB232M | 功能描述:界面模塊 USB-UART Adapter RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-USB232M-G | 功能描述:界面模塊 USB-UART Adapter RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-USB232M-G2 | 功能描述:MODULE USB-TO-TTL SRL UART CONV 制造商:dlp design inc. 系列:- 零件狀態:在售 類型:USB 至串行 轉換自（適配器端）:USB - B 2.0 母頭 轉換至（適配器端）:DIL（Dual Inline） 接口:UART 特性:- 包括:- 標準包裝:1 |
| DLP-USB232R | 功能描述:界面模塊 USB-TO-SERIAL UART INTERFACE MODULE RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。