- 您現在的位置：買賣IC網 > PDF目錄376960 > DS1809Z-010 Dallastat, 64-position linear taper PDF資料下載
參數資料
| 型號： | DS1809Z-010 |
| 英文描述： | Dallastat, 64-position linear taper |
| 中文描述： | Dallastat，64位線性錐 |
| 文件頁數： | 1/8頁 |
| 文件大小： | 87K |
| 代理商： | DS1809Z-010 |
1 of 8
101999
FEATURES
§
64-position linear taper
§
Two nonvolatile wiper storage options
§
Operates from +2.7 to +5.5-volt supplies
§
Operating Temperature Range:
- Industrial: -40
°
C to +85
°
C
§
Electronic interface provides either digital or
pushbutton control
§
Low-cost alternative to mechanical solutions
§
Standard Resistance Values
- DS1809-010
10 k
- DS1809-050
50 k
- DS1809-100
100 k
PIN DESCIPTION
V
CC
R
H
R
L
R
W
UC
DC
STR
GND
- Supply Voltage
- High End of Resistor
- Low End of Resistor
- Wiper Terminal
- Up Control Input
- Down Control Input
- Storage Enable Input
- Ground
PIN ASSIGNMENT
DESCRIPTION
The DS1809 Dallastat is a nonvolatile digitally controlled potentiometer that provides 64 uniform wiper
positions over the entire resistor range; including the high-end and low-end terminals of the device. The
DS1809 is a low power, low voltage device capable of operating from power supplies of +2.7V to +5.5V.
The device is ideal for low-power, portable, or battery powered applications.
Wiper position is maintained in the absence of power. This is accomplished via the use of an EEPROM
cell array. The device provides for two storage methods, which include an auto-store capability and a
command-initiated storage function. The EEPROM cell array is specified to accept greater than 50k
writes. Storage of the wiper position is discussed in the Wiper Storage section of this datasheet.
Wiper positioning is controlled via a patented dual pushbutton (or contact closure) interface. For simple
pushbutton-controlled applications or CPU-generated control signals, external debounce circuitry is not
needed. The control interface will support both repetitive pulse inputs and continuous pulse (“push-and-
hold”) inputs. Repetitive pulse and continuous pulse control as well as timing diagrams are discussed in
the section entitled “OPERATION.”
DS1809
Dallastat
www.dalsemi.com
R
H
1
8
V
CC
UC
2
7
DC
STR
3
6
R
W
R
L
4
5
GND
8-Pin DIP
8-Pin SOIC (150-mil)
8-Pin μSOP (118-mil)
相關PDF資料 |
PDF描述 |
|---|---|
| DS1809Z-050 | Dallastat, 64-position linear taper |
| DS1809Z-100 | Dallastat, 64-position linear taper |
| DS1809-050 | Dallastat, 64-position linear taper |
| DS1809-100 | Dallastat, 64-position linear taper |
| DS1809 | Dallastat, 64-position linear taper |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1809Z-010/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS1809Z-010+ | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809Z-010+C | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809Z-010+T&R | 制造商:Maxim Integrated Products 功能描述:SINGLE, 64-POSITION DIGITAL POTENTIOMETER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:DALLASTAT 10KOHM 8L 150 MIL SOIC |
| DS1809Z-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。