- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1821C+ (Maxim Integrated)IC THERMOMETER/STAT PROG 3-TO92 Datasheet資料下載
參數資料
| 型號： | DS1821C+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 6/19頁 |
| 文件大小： | 793K |
| 描述： | IC THERMOMETER/STAT PROG 3-TO92 |
| 標準包裝： | 500 |
| 系列： | 1-Wire® |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±1°C |
| 拓撲： | 比較器，寄存器庫 |
| 輸出類型： | 數字 |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | TO-226-3、TO-92-3 標準主體 |
| 供應商設備封裝： | TO-92-3 |
| 包裝： | 管件 |
DS1821
6 of 19
TEMPERATURE/DATA RELATIONSHIP Table 2
TEMPERATURE
DIGITAL OUTPUT
Binar
DIGITAL OUTPUT
Hex
+125癈*
0111 1101
7Dh
+85癈
0101 0101
55h
+25癈
0001 1001
19h
0癈
0000 0000
00h
-1癈
1111 1111
FFh
-25癈
1110 0111
E7h
-55癈
1100 1001
C9h
HIGH-RESOLUTION TEMPERATURE READINGS
The user can calculate temperature values with higher than 8-bit resolution using the data remaining in
the counter and slope accumulator when the temperature conversion is complete. To do this the user must
first read the temperature from the 8-bit temperature register. This value is called TEMP_READ in the
high-resolution equation (see Eq. 1). The 9-bit counter value must then be obtained by issuing the Read
Counter [A0h] command. This value is the count remaining in the counter at the end of the gate period
and is called COUNT_REMAIN in Eq. 1. Next the Load Counter [41h] command must be issued, which
loads the 9-bit slope accumulator value into the counter register. The slope accumulator value (called
COUNT_PER_C in Eq. 1) can then be read from the counter by again issuing the Read Counter [A0h]
command. The slope accumulator value is called COUNT_PER_C because it represents the number of
counts needed for an accurate measurement at a given temperature (i.e., the counts per degree C). The
high-resolution temperature can then be calculated using Eq. 1:
Eq. 1)
TEMPERATURE = TEMP_READ 0.5 +
C
PER
COUNT
REMAIN
COUNT
C
PER
COUNT
_
_
)
_
_
_
(
High-resolution temperature readings cannot be used while in continuous conversion mode. Also, the
Read Counter [A0h] and Load Counter [41h] commands must not be used while in continuous conversion
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1825U+T&R | IC THERMOMETER DIGITAL 8-USOP |
| DS1842N+T&R | IC CURRENT MONITOR 14TDFN |
| DS18B20+PAR | IC THERM MICROLAN PROG-RES TO-92 |
| DS18B20Z/T&R | IC THERM MICROLAN PROG-RES 8SOIC |
| DS2740U+T&R | IC CURRENT GAUGE(15BIT) 8UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1821C+ | 功能描述:恒溫器 Programmable Digital Thermo-stat/monitor RoHS:否 制造商:Maxim Integrated 功能: 開路溫度: 閉合溫度: 準確性:+/- 1 C 溫度范圍:- 55 C to + 125 C 電流額定值:500 uA 電壓額定值:2.7 V to 5.5 V 產品:Thermostats |
| DS1821-C02 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1821-C04 | 制造商:DSC 功能描述: |
| DS1821S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1821S/T&R | 制造商:Maxim Integrated Products 功能描述:PROGRAM THERMOSTAT 208ML 8-SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT PROG 8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。