key features brought by lpc2114/2124/01 devices

• fast gpio ports enable port pin toggling up to 3.5 times faster than the original device. they also allow for a port pin to be read at any time regardless of its function.
• dedicated result registers for adc(s) reduce interrupt overhead. the adc pads are 5 v tolerant when configured for digital i/o function(s).
• uart0/1 include fractional baud rate generator, auto-bauding capabilities and handshake flow-control fully implemented in hardware.
• buffered ssp serial controller supporting spi, 4-wire ssi, and microwire formats.
• spi programmable data length and master mode enhancement.
• diversified code read protection (crp) enables different security levels to be implemented. this feature is available in lpc2114/2124/00 devices as well.
• general purpose timers can operate as external event counters.

key features common for all devices

• 16/32-bit arm7tdmi-s microcontroller in a tiny lqfp64 package.
• 16 kb on-chip static ram.
• 128/256 kb on-chip flash program memory. 128-bit wide interface/accelerator enables high speed 60 mhz operation.
• in-system programming (isp) and in-application programming (iap) via on-chip bootloader software. flash programming takes 1 ms per 512 b line. single sector or full chip erase takes 400 ms.
• embeddedice-rt interface enables breakpoints and watch points. interrupt service routines can continue to execute whilst the foreground task is debugged with the on-chip realmonitor software.
• embedded trace macrocell (etm) enables non-intrusive high speed real-time tracing of instruction execution.
• four-channel 10-bit adc with conversion time as low as 2.44 us.
• two 32-bit timers (with four capture and four compare channels), pwm unit (six outputs), real-time clock (rtc) and watchdog.
• multiple serial interfaces including two uarts (16c550), fast i²c-bus (400 kbit/s) and two spis.
• 60 mhz maximum cpu clock available from programmable on-chip phase-locked loop with settling time of 100 us.
• vectored interrupt controller with configurable priorities and vector addresses.
• up to forty-six 5 v tolerant general purpose i/o pins. up to nine edge or level sensitive external interrupt pins available.
• on-chip crystal oscillator with an operating range of 1 mhz to 30 mhz.
• two low power modes, idle and power-down.
• processor wake-up from power-down mode via external interrupt.
• individual enable/disable of peripheral functions for power optimization.
• dual power supply:
  • cpu operating voltage range of 1.65 v to 1.95 v (1.8 v +- 0.15 v).
  • i/o power supply range of 3.0 v to 3.6 v (3.3 v +- 10 pct) with 5 v tolerant i/o pads. 16/32-bit arm7tdmi-s processor.

  lpc2100系列基于一個支持實時仿真和跟蹤的16/32位arm7tdmi-s cpu,并帶有128/256 k字節(kb)嵌入的高速flash存儲器。128位寬度的存儲器接口和獨特的加速結構使32位代碼能夠在最大時鐘速率下運行。對代碼規模有嚴格控制的應用可使用16位thumb模式將代碼規模降低超過30%,而性能的損失卻很小。
  由于lpc2100系列采用非常小的64腳封裝、極低的功耗、多個32位定時器、4路10位adc、pwm輸出以及多達9個外部中斷,這使它們特別適用于工業控制、醫療系統、訪問控制和電子收款機(pos)等應用領域。由于內置了寬范圍的串行通信接口,它們也非常適合于通信網關、協議轉換器、嵌入式軟件調制解調器以及其它各種類型的應用。后續的器件還將以太網、802.11以及usb功能。

  • 16/32位arm7tdmi-s核,超小lqfp和hvqfn封裝；
  • 16/32/64kb片內sram；
  • 128/256kb片內flash程序存儲器；
  • 128位寬度接口/加速器可實現高達60 mhz工作頻率；
  • 通過片內boot裝載程序?qū)崿F(xiàn)在系統編程(isp)和在應用編程(iap)；
  • embedded ice可實現斷點和觀察點；
  • 嵌入式跟蹤宏單元(etm)支持對執行代碼進行無干擾的高速實時跟蹤；
  • 10位a/d轉換器,轉換時間低至2.44μs；
  • can接口,帶有先進的驗收濾波器；
  • 多個串行接口,包括2個16c550工業標準uart、高速i2c接口(400 khz)和2個spi接口。