
E L E C T R O N I C S I N C .
TEL: (818) 892-0761
FAX: (818) 894-5791
http://www.pca.com
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
EP9100 to EP9129 &
EP9100-RC to EP9129-RC
Add “-RC” after part number for RoHS Compliant
Product performance is limited to specified parameters. Data is subject to change without prior notice.
CS9810-XX & -RC Rev. A1 1/31/06 RR
Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25
Tap Delays
(
±5% or ± 2nS)
5
6
7
8
9
10
12
15
30
Total Delay
(
±5% or ± 2nS)
25
30
35
40
45
50
60
7
J-Lead
Part Number
EP9108(-RC)
EP9109(-RC)
EP9110(-RC)
EP9111(-RC)
EP9112(-RC)
EP9113(-RC)
EP9114(-RC)
Tap Delays
(
±5% or ± 2nS)
20
25
30
35
40
45
50
100
Total Delay
(
±5% or ± 2nS)
100
125
150
175
200
225
250
J-Lead
Part Number
EP9100(-RC)
EP9101(-RC)
EP9102(-RC)
EP9103(-RC)
EP9104(-RC)
EP9105(-RC)
EP9106(-RC)
EP9107(-RC)
Whichever is greater. Delay times referenced from input to leading edges at 25°C, 5.0V, with no load.
Input Pulse Test Conditions @ 25° C
EIN
PW
TRI
PRR
Pulse Input Voltage
Pulse Width % of Total Delay
Pulse Rise Time (0.75 - 2.4 Volts)
Pulse Repetition Rate @ Td
≤
200 nS
Pulse Repetition Rate @ Td > 200 nS
Supply Voltage
VCC
3.2
110
2.0
1.0
100
5.0
Unit
Volts
%
nS
MHz
KHz
Volts
Schematic
2
15
28 17 26
12
18
OUTPUT
GROUND
INPUT
4
VCC
Notes :
1. Assembly Process
(Solder Composition)
2. Peak Solder Rating
(per IPC/JEDEC J-STD-020C)
4. Weight
3. Moisture Sensitive Levels (MSL)
(per IPC/JEDEC J-STD-020C)
(Leadframe)
(Assembly Solder)
5. Packaging Information
(Tube)
EP91XX-RC
Sn
260°C
TBD grams
4
(72 hours,
≤
30°C/60%RH)
SnPb
(RoHS exemption 7a)
45 pieces/tube
EP91XX
SnPb
SnPb
225°C
TBD grams
3
(168 hours,
≤
30°C/60%RH)
45 pieces/tube
10
12
14
16
18
20
24
15
18
21
24
27
30
36
45
20
24
28
32
36
40
48
60
40
50
60
70
80
90
60
75
90
105
120
135
150
80
100
120
140
160
180
200
DC Electrical Characteristics
Parameter
VOH
High-Level Output Voltage
VOL
Low-Level Output Voltage
VIK
Input Clamp Voltage
IIH
High-Level Input Current
Test Conditions
VCC = min. VIL= max. IOH = max
VCC = min. VH = min. IOL= max
VCC = min. II = IIK
VCC = max. VIN = 2.7V
VCC = max. VIN = 5.25V
VCC = max. VIN = 0.5V
Unit
V
V
V
μA
mA
mA
mA
Min.
2.7
Max.
0.5
-1.2
50
1.0
-2
-100
IIL
IOS
Low-Level Input Current
Short Circuit Output Current VCC = max. VOUT = 0.
-40
(One output at a time)
VCC = max. VIN = OPEN
VCC = max. VIN = 0
Td
≤
500 nS (0.75 to 2.4 Volts)
Td > 500 nS
VCC = max. VOH = 2.7V
VCC = max. VOL = 0.5V
ICCHHigh-Level Supply Current
ICCL
Low-Level Supply Current
TRO
Output Rise Time
75
75
4
5
mA
mA
nS
nS
NH
NL
Fanout High-Level Output
Fanout Low-Level Output
20 TTL Load
10 TTL Load
Recommended Operating Conditions Min.
VCC
Supply Voltage
VIH
High-Level Input Voltage
VIL
Low-Level Input Voltage
IIK
Input Clamp Current
IOH
High-Level Output Current
IOL
Low-Level Output Current
PW*
Pulse Width of Total Delay
d*
Duty Cycle
TA
Operating Free-Air Temperature
Max.
5.25
Unit
V
V
V
mA
mA
mA
%
%
°C
*These two values are inter-dependent.
4.75
2.0
0.8
-18
-1.0
20
40
40
+70
0
28 Pin SMD 5 Tap TTL Compatible
Active Delay Lines
Gull-Wing
Part Number
EP9123(-RC)
EP9124(-RC)
EP9125(-RC)
EP9126(-RC)
EP9127(-RC)
EP9128(-RC)
EP9129(-RC)
Gull-Wing
Part Number
EP9115(-RC)
EP9116(-RC)
EP9117(-RC)
EP9118(-RC)
EP9119(-RC)
EP9120(-RC)
EP9121(-RC)
EP9122(-RC)
J-Lead Package
1 28
.018 x .008
(.457 x .203)
Tin Plated Kova
.025/.045
(.635/1.14)
Suggested Solder
Pad Layout
(9.27)
PCA
EP9100(-RC)
D.C.
4
26
12
18
.175 Max.
(4.45)
.450 Max.
(11.43)
.475
(12.07)
.365
.055
(1.40)
.030
(.762)
.370
Max.
(9.40)
.050
Typ.
(1.27)
.050 Typ.
(1.27)
.050 Typ.
(1.27)
.018 x .008
(.457 x .203)
Tin Plated Kovar
Suggested Solder
Pad Layout
.175 Max.
(4.45)
.450 Max.
(11.43)
.475
(12.07)
.365
(9.27)
.055
(1.40)
.030
(.762)
.370
Max.
(9.40)
.050
Typ.
(1.27)
.050 Typ.
(1.27)
4
1 28 26
12
18
PCA
EP9129(-RC)
D.C.
Gull Wing Package