- 您現在的位置：買賣IC網 > PDF目錄375700 > F2M03C2 (Electronic Theatre Controls, Inc.) Class 2 Bluetooth⑩ Module PDF資料下載
參數資料
| 型號： | F2M03C2 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Class 2 Bluetooth⑩ Module |
| 中文描述： | ⑩2級藍牙模塊 |
| 文件頁數： | 27/46頁 |
| 文件大小： | 768K |
| 代理商： | F2M03C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Rev: 13 September 2005
Class 2 Bluetooth module - F2M03C2
Datasheet
6.2.6
Suspend Current
USB devices that run off VBUS must be able to enter a suspended state, whereby they consume less that
0.5mA from VBUS. The voltage regulator circuit itself should draw only a small quiescent current (typically
less than 100μA) to ensure adherence to the suspend-current requirement of the USB specification. This is
not normally a problem with modern regulators. Ensure that external LEDs can be turned off by F2M03. The
entire circuit must be able to enter the suspend mode.
6.2.7 Detach and Wake_Up Signalling
F2M03 can provide out-of-band signalling to a host controller by using the dedicated control lines called
‘USB_DETACH’ and ‘USB_WAKE_UP’. These are outside the USB specification (no wires exist for them
inside the USB cable), but can be useful when embedding F2M03 into a circuit where no external USB is
visible to the user. Both control lines are shared with PIO pins and can be assigned to any PIO pin by
firmware settings (contact Free2move)
USB_DETACH, is an input which, when asserted high, causes F2M03 to put USB_D- and USB_D+ in a
high-impedance state and to 1.5kO pull-up resistor on USB_D+. This detaches the device from the bus and
is logically equivalent to unplugging the device. When USB_DETACH is taken low, F2M03 will connect
back to USB and await enumeration by the USB host.
USB_WAKE_UP, is an active high output (used only when USB_DETACH is active) to wake up the host
and allow USB communication to recommence. It replaces the function of the software USB WAKE_UP
message (which runs over the USB cable proper), and cannot be sent while F2M03 is effectively
disconnected from the bus.
USB_DETACH and USB_WAKE_UP Signal
6.2.8 USB Driver
A USB Bluetooth device driver is required to provide a software interface between F2M03 and Bluetooth
applications running on the host.
2003 Free2move AB
Page 27(46)
相關PDF資料 |
PDF描述 |
|---|---|
| F2M03C2001 | Class 2 Bluetooth⑩ Module |
| F2UGRSP01ABC | Pushbutton Switches |
| F2UAOR | Pushbutton Switches |
| F2UAOR01A | Pushbutton Switches |
| F2UAOR01AAU | Pushbutton Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F2M03C2001 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Class 2 Bluetooth? Module |
| F2M03C2-101 | 制造商:Free2move 功能描述:MODULE SPP BLUETOOTH CLASS 2 |
| F2M03G-KIT-1 | 功能描述:KIT EVAL G MOD SNGL (NO OEM BRD) RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
| F2M03GLA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low power Bluetooth? Module with antenna |
| F2M03GLA-S01 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR SPP W/ANT |
發布緊急采購，3分鐘左右您將得到回復。