- 您現在的位置：買賣IC網 > PDF目錄375704 > F362GA (Fujitsu Limited) 32-BIT RISC MICROCONTROLLER PDF資料下載
參數資料
| 型號： | F362GA |
| 廠商： | Fujitsu Limited |
| 英文描述： | 32-BIT RISC MICROCONTROLLER |
| 中文描述： | 32位RISC微控制器 |
| 文件頁數： | 38/206頁 |
| 文件大小： | 811K |
| 代理商： | F362GA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁
MB91360G Series
38
I
HANDLING DEVICES
1.
Preventing latch-up
Latch-up may occur in a CMOS IC if a voltage greater than V
DD
or less than V
SS
is applied to an input or output
pin or if the voltage applied between V
DD
and V
SS
exceeds the rating. If latch-up occurs, the power supply current
increases rapidly resulting in thermal damage to circuit elements. Therefore, ensure that maximum ratings are
not exceeded in circuit operation.
Connecting unused pins
2.
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be tied to V
DD
or V
SS
through resistors. In this case those resistors should be more
than 2 KOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
The resistor of more than 2 KOhm is used to limit currents through the protection diodes. In case of voltages at
the not used pin of 0.3 V or more below V
SS
or 0.3 V or more above V
DD
currents which could cause latch-up will
flow through those diodes.
External reset input
3.
When inputting an “L” level to the INITX pin, hold this low level at the INITX pin long enough so that after release
of the low level at INITX and the passing of the built in waiting time stable oscillation of the oscillation circuit is
achieved. INITX must be pulled low for at least 8 cycles of the 4 MHz oscillation clock.
Power supply pins
4.
All V
DD
pins should be connected to the same potential (exception can be the external bus interface on F362GA
and F369GA) . The analogue supply voltage (AV
CC
) must not be turned on before the digital supply voltage. If
the external bus interface is supplied with 3.3 V this voltage also must not be turned on before the 5 V digital
voltage has been switched on. If the supply voltage to the external bus interface is switched off (it may not be
tristate but should be pulled low) it must be made sure that all related signals do not have a voltage higher than
this pulled down supply.
When multiple V
DD
and V
SS
pins are provided, be sure to connect all V
DD
and V
SS
pins to the power supply or
ground externally. Although pins at the same potential are connected together in the internal device design so
as to prevent malfunctions such as latch-up, connecting all V
DD
and V
SS
pins appropriately minimizes unwanted
radiation, prevents malfunction of strobe signals due to increases in the ground level, and keeps the overall
output current rating.
Also, take care to connect V
DD
and V
SS
to current source in the lowest possible impedance.
Connection of a ceramic bypass capacitor of approximately 0.1
μ
F between V
DD
and V
SS
close to the device is
recommended.
The MB91360G series contains a regulator. To use the device with the 5-V power supply, supply 5-V power to
the V
CC
pins and be sure to connect a bypass capacitor of 10
μ
F parallel to 10 nF to the V
CC
3C pin for the regulator.
[Use with 5-V power supply]
5 V
5 V
10
μ
F
10 nF
V
CC
3C
V
CC
AV
CC
AVRH
AV
SS
V
SS
GND
相關PDF資料 |
PDF描述 |
|---|---|
| F369GA | 32-BIT RISC MICROCONTROLLER |
| F3D480M20A | VI Chip PFM Power Factor Module |
| F3D480T20A | VI Chip PFM Power Factor Module |
| F3S49092 | 20A/10A, 12V, 0.060/0.140 Ohm, Logic Level, Complementary Power MOSFET |
| F40UP20DN | Ultrafast Recovery Power Rectifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F-362XP | 功能描述:電源變壓器 10VA 20V CT @ 0.5A PC Mount RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in |
| F36304-000 | 制造商:TE Connectivity 功能描述:VARISTOR 180V 4.5KA DISC 14MM 制造商:TE Connectivity 功能描述:VARISTOR 180VDC 14MM STRGT LEAD |
| F36-350 | 功能描述:電源變壓器 12VA 36V CT @ 0.35A Split Pack RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in |
| F36-350-C2 | 制造商:Triad Magnetics 功能描述:Transformer, class 2/3, 6-pin, 12VA, 115V x 36VCT at 0.35A, 18V at 0.7A |
| F36-350-C2-B | 制造商:Triad Magnetics 功能描述:XFRMR LAMINATED 12VA THRU HOLE |
發布緊急采購，3分鐘左右您將得到回復。