- 您現在的位置：買賣IC網 > PDF目錄375714 > FA3647P (FUJI ELECTRIC CO LTD) PWM control IC with light load power saving function For Switching Power Supply Control PDF資料下載
參數資料
| 型號： | FA3647P |
| 廠商： | FUJI ELECTRIC CO LTD |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM control IC with light load power saving function For Switching Power Supply Control |
| 中文描述： | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | DIP-8 |
| 文件頁數： | 13/21頁 |
| 文件大小： | 406K |
| 代理商： | FA3647P |
FA3641P(N), FA3647P(N)
70
Fig. 19 Startup circuit (1)
Fig. 20 Startup circuit (2)
2. Deciding the startup circuit
These ICs, which use CMOS process, consume less current,
and therefore can use larger startup resistance than the
conventional bipolar type of IC.
To decide the startup resistance, the following conditions must
be satisfied:
(a) The IC is started when the power is turned on.
(b) The IC consumption current is supplied during latch
mode operation to maintain the latch state.
(c) The IC consumption current is supplied during the off state
under the on/off function to maintain the off state.
However, these are the minimum conditions for using the IC.
The startup time required for the power supply must also be
decided on.
2.1Connecting a startup resistor before rectification
(AC line)
When the startup resistor is connected before rectification (AC
line) as shown in Figure 19, the voltage applied to the startup
resistor forms a half-wave rectified waveform of the AC input
voltage.
Startup resistor R1 must satisfy the three equations shown
below. Select a smaller-side value for R1 in consideration of the
temperature characteristics.
(a) To supply startup current 30
μ
A at ON threshold voltage
17.5V (max.) of UVLO:
2
Vac
–
17.5
R1 [k
] <
π
0.03
........................................ (8)
(b) To supply IC consumption current 100
μ
A (max.) (Vcc =10V)
in latch mode:
2
Vac
–
10
R1 [k
] <
π
0.1
....................................... (9)
(c) To supply IC consumption current 200
μ
A (max.) (Vcc =17V)
in the off state under the on/off function:
2
Vac
–
17
R1 [k
] <
π
0.2
......................................(10)
R1:
Vac: Effective value of AC input voltage [V]
Startup resistance [k
]
If neither the latch mode operation nor the on/off functions are
used, only the expression in (8) needs to be satisfied.
In this method, the supply current to the IC via the start-up
resistor is stopped when AC input is shut down. Therefore, after
latch mode operation, shutting the AC input down resets the
latch mode in a very short period of time.
2.2 Connecting the startup resistor after rectification
(DC line)
When the startup resistor is connected after rectification (DC
line) as shown in Figure 20, the voltage applied to the startup
resistor becomes the peak value of the AC input voltage.
Startup resistor R1 must satisfy the three equations shown
below. Select a smaller-side value for R1 in consideration of
temperature characteristics.
(a) To supply startup current 30
μ
A at ON threshold voltage
17.5V (max.) of UVLO:
..................................(11)
R1 [k
] < 2
Vac
–
17.5
0.03
相關PDF資料 |
PDF描述 |
|---|---|
| FA365 | THIN SMD HIGH-FREQUENCY CRYSTAL UNIT |
| FA-365 | THIN SMD HIGH-FREQUENCY CRYSTAL UNIT |
| FA3675F | For Switching Power Supply Control |
| FA3863X | SUPER BRIGHT LED |
| FA38SA50LC | RECTIFIER BRIDGE 25A 200V 350A-ifsm 1.05V-vf 10uA-ir GBJ 15/TUBE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FA3647P-D1 | 制造商:Fuji Electric 功能描述: |
| FA365 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:THIN SMD HIGH-FREQUENCY CRYSTAL UNIT |
| FA-365 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:THIN SMD HIGH-FREQUENCY CRYSTAL UNIT |
| FA-365 14.31818MHZ 50PPM 16PF | 制造商:Epson Toyocom Corporation 功能描述:XTAL FA-365 14.31818MHZ 50PPM 16PF |
| FA-365 16.0000MB-G3 | 功能描述:CRYSTAL 16.0000MHZ 20PF SMD RoHS:是 類別:晶體和振蕩器 >> 晶體 系列:FA-365 標準包裝:1 系列:ABLS2 類型:MHz 晶體 頻率:3.579545MHz 頻率穩定性:±30ppm 頻率公差:±30ppm 負載電容:18pF ESR（等效串聯電阻）:180 歐姆 工作模式:基諧 工作溫度:-40°C ~ 85°C 額定值:- 安裝類型:表面貼裝 封裝/外殼:HC49/US 尺寸/尺寸:0.449" L x 0.185" W（11.40mm x 4.70mm） 高度:0.130"（3.30mm） 包裝:剪切帶 (CT) 產品目錄頁面:1683 (CN2011-ZH PDF) 其它名稱:535-9855-1 |
發布緊急采購，3分鐘左右您將得到回復。