- 您現在的位置：買賣IC網 > PDF目錄375719 > FAN2011 (Fairchild Semiconductor Corporation) 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator PDF資料下載
參數資料
| 型號： | FAN2011 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| 中文描述： | 1.5A的低電壓電流模式同步PWM降壓穩壓器 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 240K |
| 代理商： | FAN2011 |
8
www.fairchildsemi.com
FAN2011/FAN2012 Rev. 1.0.2
F
Inductor Selection
The inductor parameters directly related to device performances
are saturation current and dc resistance. The FAN2011/
FAN2012 operates with a typical inductor value of 3.3μH. The
lower the dc resistance, the higher the ef
fi
ciency. For saturation
current, the inductor should be rated higher than the maximum
load current plus half of the inductor ripple current that is calcu-
lated as follows:
where:
I
L
= Inductor Ripple Current
f = Switching Frequency
L = Inductor Value
Some recommended inductors are suggested in the table
below:
Table 1: Recommended Inductors
Capacitors Selection
For best performances, a low ESR input capacitor is required. A
ceramic capacitor of at least 10μF, placed as close to the V
IN
and AGND pins of the device is recommended. The output
capacitor determines the output ripple and the transient
response.
Table 2: Recommended Capacitors
PCB Layout Recommendations
The inherently high peak currents and switching frequency of
power supplies require a careful PCB layout design. Therefore,
use wide traces for high current paths and place the input
capacitor, the inductor, and the output capacitor as close as
possible to the integrated circuit terminals. In order to minimize
voltage stress to the device resulting from ever present switch-
ing spikes, use an input bypass capacitor with low ESR. Use of
an external Schottky diode with its anode connected to SW
node and cathode connected to PV
IN
further reduces switching
spikes. Note that the peak amplitude of the switching spikes
depends upon the load current; the higher the load current, the
higher the switching spikes.
The resistor divider that sets the output voltage should be
routed away from the inductor to avoid RF coupling. The ground
plane at the bottom side of the PCB acts as an electromagnetic
shield to reduce EMI. The recommended PCB layout is shown
below in Figure 5.
Figure 5. Recommended PCB Layout
Inductor Value
Vendor
Part Number
3.3μH
Panasonic
ELL6PM3R3N
3.3μH
Murata
LQS66C3R3M04
Capacitor
Value
Vendor
Part Number
10μF
Taiyo Yuden
JMK212BJ106MG
JMK316BJ106KL
TDK
C2012X5ROJ106K
C3216X5ROJ106M
Murata
GRM32ER61C106K
I
L
V
OUT
1
-----–
V
V
L
)
f
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| FAN2011I | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2012IMPX | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2011IMPX | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2011MPX | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2012 | 1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN2011_06 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2011_ACA3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN2011EMPX | 功能描述:直流/直流開關轉換器 ANG FG 1.5a Syncr. Switcher RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| FAN2011I | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
| FAN2011IMPX | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:1.5A Low Voltage Current Mode Synchronous PWM Buck Regulator |
發布緊急采購，3分鐘左右您將得到回復。