- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5009M (FAIRCHILD SEMICONDUCTOR CORP) Dual Bootstrapped 12V MOSFET Driver PDF資料下載
參數資料
| 型號： | FAN5009M |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | MOSFETs |
| 英文描述： | Dual Bootstrapped 12V MOSFET Driver |
| 中文描述： | HALF BRDG BASED MOSFET DRIVER, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 167K |
| 代理商： | FAN5009M |
8
REV. 1.0.5 7/22/04
FAN5009
PRODUCT SPECIFICATION
Circuit Description
The FAN5009 is a dual MOSFET driver optimized for driv-
ing N-channel MOSFETs in a synchronous buck converter
topology. A single PWM input signal is all that is required to
properly drive the high-side and the low-side MOSFETs.
Each driver is capable of driving a 3nF load at speeds up to
500kHz.
For a more detailed description of the FAN5009 and its
features, refer to the Internal Block Diagram and Figure 1.
Low-Side Driver
The low-side driver (LDRV) is designed to drive a ground-
referenced low R
DS(on)
N-channel MOSFETs. The bias for
LDRV is internally connected between VCC and PGND.
When the driver is enabled, the driver’s output is 180° out of
phase with the PWM input. When the FAN5009 is disabled
(OD = 0V), LDRV is held low.
High-Side Driver
The high-side driver (HDRV) is designed to drive a floating
N-channel MOSFET. The bias voltage for the high-side
driver is developed by a bootstrap supply circuit, consisting
of the internal diode and external bootstrap capacitor
(C
BOOT
) .
During start-up, SW is held at PGND, allowing C
charge to VCC through the internal diode. When the PWM
input goes high, HDRV will begin to charge the high-side
MOSFET’s gate (Q1). During this transition, charge is
removed from C
BOOT
and delivered to Q1’s gate. As Q1
turns on, SW rises to V
IN
, forcing the BOOT pin to
V
IN
+V
C(BOOT)
, which provides sufficient V
GS
enhancement
for Q1.
BOOT
to
To complete the switching cycle, Q1 is turned off by pulling
HDRV to SW. C
BOOT
is then recharged to VCC when SW
falls to PGND.
HDRV output is in phase with the PWM input. When the
driver is disabled, the high-side gate is held low.
Adaptive Gate Drive Circuit
The FAN5009 embodies an advanced design that ensures
minimum MOSFET dead-time while eliminating potential
shoot-through (cross-conduction) currents. It senses the
state of the MOSFETs and adjusts the gate drive, adaptively,
to ensure they do not conduct simultaneously. Refer to
Figure 4 for the relevant timing waveforms.
To prevent overlap during the low-to-high switching transi-
tion (Q2 OFF to Q1 ON), the adaptive circuitry monitors the
voltage at the LDRV pin. When the PWM signal goes
HIGH, Q2 will begin to turn OFF after some propagation
delay (t
pdl(LDRV)
).
Once the LDRV pin is discharged below ~1.2V, Q1 begins to
turn ON after adaptive delay t
pdh(HDRV)
.
To preclude overlap during the high-to-low transition (Q1
OFF to Q2 ON), the adaptive circuitry monitors the voltage
at the SW pin. When the PWM signal goes LOW, Q1 will
begin to turn OFF after some propagation delay (t
pdl(HDRV)
).
Once the SW pin falls below ~2.2V, Q2 begins to turn ON
after adaptive delay t
pdh(LDRV)
.
Additionally, V
GS
of Q1 is monitored. When V
GS(Q1)
is
discharged below ~1.2V, a secondary adaptive delay is initi-
ated, which results in Q2 being driven ON after t
pdh(ODRV)
,
regardless of SW state. This function is implemented to
ensure C
BOOT
is recharged each switching cycle, particularly
for cases where the power convertor is sinking current and
SW voltage does not fall below the 2.2V adaptive threshold.
Secondary delay t
pdh(ODRV)
is longer than t
pdh(LDRV)
.
Application Information
Supply Capacitor Selection
For the supply input (V
CC
) of the FAN5009, a local ceramic
bypass capacitor is recommended to reduce the noise and to
supply the peak current. Use at least a 1μF, X7R or X5R
capacitor. Keep this capacitor close to the FAN5009 V
CC
and PGND pins.
Bootstrap Circuit
The bootstrap circuit uses a charge storage capacitor
(C
BOOT
) and the internal diode, as shown in Figure 1. Selec-
tion of these components should be done after the high-side
MOSFET has been chosen. The required capacitance is
determined using the following equation:
where Q
G
is the total gate charge of the high-side MOSFET,
and
V
BOOT
is the voltage droop allowed on the high-side
MOSFET drive. For example, the Q
G
of the FDD6696 is
about 35nC @ 12V
GS
. For an allowed droop of ~300mV, the
required bootstrap capacitance is 100nF. A good quality
ceramic capacitor must be used.
The average diode forward current, I
F(AVG)
, can be
estimated by:
where F
SW
is the switching frequency of the controller.
The peak surge current rating of the internal diode should be
checked in-circuit, since this is dependent on the equivalent
impedance of the entire bootstrap circuit, including the PCB
traces. For applications requiring higher I
F
, an external
diode may be used in parallel to the internal diode.
C
BOOT
Q
BOOT
----V
=
(1)
I
F AVG
)
Q
GATE
F
SW
×
=
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5009MX | Dual Bootstrapped 12V MOSFET Driver |
| FAN5009MPX | Dual Bootstrapped 12V MOSFET Driver |
| FAN5018B | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5018BMTCX | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019B | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5009MPX | 功能描述:功率驅動器IC ANG FG Dual Bootstrp 12V MOSFET Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| FAN5009MX | 功能描述:功率驅動器IC Sync DC-DC MOSFET Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| FAN5017MX | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5018_BBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5018B | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controller 2-4 Phase VR10.X Controller |
發布緊急采購，3分鐘左右您將得到回復。