- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5019 (Fairchild Semiconductor Corporation) 6-Bit VID Controller 2-4 Phase VRM10.X Controller PDF資料下載
參數資料
| 型號： | FAN5019 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| 中文描述： | 6西元控制器2-4位控制器相VRM10.X |
| 文件頁數： | 2/30頁 |
| 文件大小： | 781K |
| 代理商： | FAN5019 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
FAN5019
PRODUCT SPECIFICATION
2
REV. 1.0.7 1/5/04
Pin Assignments
Pin Definitions
Pin Number
1–5
Pin Name
VID [4:0]
Pin Function Description
VID inputs.
Determines the output voltage via the internal DAC. These inputs
comply to VRM10/VRD10 specifications for static and dynamic operation. All have
internal pull-ups (1.25V for VRM10 and 2.5V for VRM9) so leaving them open
results in logic high. Leaving VID[4:0] open results in a "No CPU" condition
disabling the PWM outputs.
VID5 Input/DAC Select.
Dual function pin that is either the 12.5mV DAC LSB for
VRM10 or selects the VRM9 DAC codes when forced higher than Vtblsel(VRM9)
voltage. The truth table is as follows:
6
VID5/SEL
V
VID5/SEL
held > Vtblsel(VRM9); VRM9 DAC table is selected (See Table 3)
V
ViD5/SEL
< Vtblsel(VRM10); VRM10 DAC table is selected (See Table 2) and
V
ViD5/SEL
pin is used as VID5 input.
Feedback Return.
Error Amp and DAC reference point.
Feedback Input.
Inverting input for Error Amp this pin is used for external
compensation. This pin can also be used to introduce DC offset voltage to the
output.
Error Amp output.
This pin is used for external compensation.
Power Good output.
This is an open-drain output that asserts when the output
voltage is within the specified tolerance. It is expected to be pulled up to an external
voltage rail.
Enable.
Logic signal that enables the controller when logic high.
Soft-start and Current Limit Delay.
An external resistor and capacitor sets the
softstart ramp rate and the over-current latch off delay.
Switching Frequency Adjust.
This pin adjusts the output PWM switching
frequency via an external resistor.
PWM Current Ramp Adjust.
An external resistor to Vcc will adjust the amplitude of
the internal PWM ramp.
Current Limit Adjust.
An external resistor sets the current limit threshold for the
regulator circuit. This pin is internally pulled low when EN is low or the UVLO circuit
is active. It is also used to enable the drivers.
7
8
FBRTN
FB
9
10
COMP
PWRGD
11
12
EN
DELAY
13
RT
14
RAMPADJ
15
ILIMIT
DELAY
VID4
VID3
VID2
VID1
VID0
COMP
CSCOMP
PWRGD
EN
CSSUM
CSREF
RT
VCC
SW2
SW3
SW4
PWM3
PWM4
PWM1
GND
FBRTN
ILIMIT
FB
RAMPADJ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
FAN5019
TSSOP-28
SW1
PWM2
VID5/SEL
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5026 | Dual DDR/Dual-output PWM Controller |
| FAN5026MTC | Dual DDR/Dual-output PWM Controller |
| FAN5026MTCX | Dual DDR/Dual-output PWM Controller |
| FAN5037 | Isolated Flyback Switching Regulator with 9V Output |
| FAN5037M | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5019_ABC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_ABC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_BBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019B | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019BMTCX | 功能描述:DC/DC 開關控制器 ANG FG PWM 4 pases controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。