欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: FAN5019MTC
廠商: FAIRCHILD SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: 6-Bit VID Controller 2-4 Phase VRM10.X Controller
中文描述: SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28
封裝: TSSOP-28
文件頁數: 27/30頁
文件大小: 781K
代理商: FAN5019MTC
PRODUCT SPECIFICATION
FAN5019
REV. 1.0.7 1/5/04
27
Figure 10. Transient Setting Waveform
Since the FAN5019 turns off all of the phases (switches
inductors to ground), there is no ripple voltage present
during load release. Thus, you do not have to add headroom
for ripple, allowing your load release V
TRANREL
to be larger
than V
TRAN1
by that amount and still be meeting spec. If
V
TRAN1
and V
TRANREL
are less than the desired final droop,
this implies that capacitors can be removed. When removing
capacitors, make sure to check the output ripple voltage as
well to make sure it is still within spec.
Layout and Component Placement
The following guidelines are recommended for optimal
performance of a switching regulator in a PC system.
Key layout issues are illustrated in Figure 11.
Figure 11. Layout Recommendations
General Recommendations
For good results, at least a four-layer PCB is
recommended. This should allow the needed versatility
for control circuitry interconnections with optimal
placement, power planes for ground, input, and output
power, and wide interconnection traces in the rest of the
power delivery current paths. Keep in mind that each
square unit of 1 ounce copper trace has a resistance of
~0.53 m
at room temperature.
Whenever high currents must be routed between PCB
layers, vias should be used liberally to create several
parallel current paths so that the resistance and inductance
introduced by these current paths is minimized and the via
current rating is not exceeded.
If critical signal lines (including the output voltage sense
lines of the FAN5019) must cross through power circuitry,
it is best if a signal ground plane can be interposed
between those signal lines and the traces of the power
circuitry to serves as a shield to minimize noise injection
into the signals..
An analog ground plane should be used both around and
under the FAN5019 for ground connections to the
components associated with the controller. This plane
should be tied to the nearest output decoupling capacitor
ground and should not tie to any other power circuitry to
prevent power currents from flowing in it.
The components around the FAN5019 should be located
close to the controller with short traces. The most
important traces to keep short and away from other traces
are the FB and CSSUM pins.
The output capacitors should be connected as close as
possible to the load (or connector) that receives the power
(e.g., a microprocessor core). If the load is distributed, the
capacitors should also be distributed, and generally in
proportion to where the load tends to be more dynamic.
Power Circuitry
The switching power path should be routed on the PCB to
encompass the shortest possible length in order to
minimize radiated switching noise energy (i.e., EMI) and
conduction losses in the board. Failure to take proper
precautions often results in EMI problems for the entire
PC system as well as noise related operational problems
in the power converter control circuitry. The switching
power path is the loop formed by the current path through
the input capacitors and the power MOSFETs including
all interconnecting PCB traces and planes. The use of
short and wide interconnection traces is especially critical
in this path for two reasons: it minimizes the inductance in
the switching loop, which can cause high-energy ringing,
and it accommodates the high current demand with
minimal voltage loss. Avoid crossing any signal lines over
the switching power path loop, described below.
相關PDF資料
PDF描述
FAN5019MTCX 6-Bit VID Controller 2-4 Phase VRM10.X Controller
FAN5019 6-Bit VID Controller 2-4 Phase VRM10.X Controller
FAN5026 Dual DDR/Dual-output PWM Controller
FAN5026MTC Dual DDR/Dual-output PWM Controller
FAN5026MTCX Dual DDR/Dual-output PWM Controller
相關代理商/技術參數
參數描述
FAN5019MTCX 功能描述:DC/DC 開關控制器 Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
FAN501MPX 制造商:Fairchild Semiconductor Corporation 功能描述:PWM CONTROLLER - Tape and Reel
FAN5020_AAC3116B WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
FAN5021_AAC3026B WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
FAN5026 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Dual DDR/Dual-output PWM Controller
主站蜘蛛池模板: 察隅县| 南昌市| 高台县| 博客| 历史| 南京市| 大方县| 双流县| 元谋县| 凤凰县| 鄯善县| 阳曲县| 且末县| 上林县| 武平县| 克什克腾旗| 陈巴尔虎旗| 阿拉善右旗| 昆明市| 夏邑县| 彰化市| 修武县| 兰坪| 宜都市| 衡南县| 新和县| 方山县| 灵川县| 平塘县| 玛曲县| 奉贤区| 庄河市| 朝阳县| 平阳县| 浦城县| 鸡西市| 花莲市| 吉隆县| 清远市| 陵川县| 英吉沙县|