- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5233 (Fairchild Semiconductor Corporation) System Electronics Regulator for Mobile PCs PDF資料下載
參數資料
| 型號： | FAN5233 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | System Electronics Regulator for Mobile PCs |
| 中文描述： | 系統的電子調節器移動PC |
| 文件頁數： | 11/15頁 |
| 文件大小： | 388K |
| 代理商： | FAN5233 |
PRODUCT SPECIFICATION
FAN5233
REV. 1.0.6 1/22/02
11
will pull down the output voltage and eventually may blow the
battery fuse. As soon as output voltage drops below the
threshold, OVP comparator is disengaged.
The OVP scheme also provides a soft crowbar function
(bang-bang control followed by blow of the fuse) which
helps to tackle severe load transients but does not invert out-
put voltage when activated—a common problem for OVP
schemes with a latch. The prevention of output inversion
eliminates the need for a Schottky diode across the load.
3.3V and 5V Under-voltage Protection
When the output voltage of either the 3.3V or 5V falls
below 75% of the nominal value, both converters, go into
under-voltage (UV) protection, after a 2usec delay. In under-
voltage protection, the high and low side MOSFETs are
turned off. Once under-voltage protection is triggered, it
remains on until power is recycled or the SDWN pin is reset.
12V Architecture
The 12V converter is a traditional non-isolated fly-back (also
known as a "boost" converter). The converter’s input voltage
is the +5V switcher output, so that +12V can only be present
if +5V is present. Also, if the external MOSFET is off, the
output of the +12V converter is +5V, not zero. This in turn
will provide non-zero output for the 12V regulator.
For complete turn-off of the 12V regulator an external
P-channel MOSFET or an LDO regulator with on/off control
may be used. If an LDO is used for 12V then the boost
converter should be set to 13.2V using the external resistor
divider network. If the 12V “boost” converter is not used,
connect VFB12 (pin 15) to 5V-ALWAYS (pin 6).
12V Loop Compensation
The 12V converter should be run in discontinuous conduc-
tion mode. In this mode, the converter will be stable if a
capacitor with suitable ESR value is selected. A 68uF
tantalum with 500mA ripple current rating and 95m
is
recommended here.
12V Protection
The 12V converter is protected against overvoltage. If the
12V feedback is more than 10–15% above the nominal set
voltage, a comparator forces the MOSFET off until the volt-
age falls below the comparator threshold.
The 12V converter is also protected against over-current. If a
short circuit pulls the output below 9V, all of the switching
converters go into UV protection, after a 2μs delay. In UV
protection, all MOSFETs are turned off. Once UV protection
is triggered, it remains on until the input power is recycled or
the SDWN is reset.
12V Softstart and Sequencing
The 12V output is started at the same time as the 5V output.
The softly rising 5V output automatically generates a softly
rising 12V output. The duty cycle of the 12V PWM is lim-
ited to prevent excessive current draw.
The 12V supply must build up a voltage higher than the
UVLO limit (9V) by the time the 5V is above its UVLO
(3.75V) in order to avoid triggering of UV protection during
soft start.
5V-ALWAYS Operation
The 5V-ALWAYS supply is generated from either the
on-chip linear regulator or through an internal switch from
the VFB pin of the 5V switching supply. The 5V-ALWAYS
supply should be decoupled to ground with a 10μF capacitor.
When the 5V switching supply is off, or if its output voltage
is not within tolerance, the 5V-ALWAYS switch is open, and
the linear regulator is on. When the 5V switching supply is
running and has an output voltage within specification, the
linear regulator is off, and the switch is on. The switch has
sufficiently low resistance that at maximum current draw on
the 5V-ALWAYS supply, the output voltage is regulated
within specifications.
The purpose of the ALWAYS supply is to provide power to
the system micro-controller (8051 class) as well as other IC’s
needing a stand-by power. The micro-controller as well as
the other IC’s could be operated from the ALWAYS supply.
5V-ALWAYS Protections
The 5V linear regulator is current limited and under-voltage
protected. Once protection is triggered the output is turned
off until power is cycled or the SDWN is reset.
Power good
Power good is asserted when both PWM Buck converters are
above specified threshold. No other regulators are monitored
by Power good. When PGOOD goes low it will stay low for
at least 10μsec (T
W
). See Figure 5.
Figure 5. PGOOD Timing Diagram
Vmain
t
PGOOD
t
Vth
Tw
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5233MTC | Analog IC |
| FAN5233MTCX | Analog IC |
| FAN5234MTC | Mobile-Friendly PWM/PFM Controller |
| FAN5234MTCX | Mobile-Friendly PWM/PFM Controller |
| FAN5234QSC | Mobile-Friendly PWM/PFM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5233MTC | 功能描述:開關變換器、穩壓器與控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5233MTCX | 功能描述:開關變換器、穩壓器與控制器 PWM Buck Controller adjustable RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5234 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Dual Mobile-Friendly PWM / PFM Controller |
| FAN5234_10 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Dual Mobile-Friendly PWM / PFM Controller |
| FAN5234MTC | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。