- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5234QSC (FAIRCHILD SEMICONDUCTOR CORP) Mobile-Friendly PWM/PFM Controller PDF資料下載
參數資料
| 型號： | FAN5234QSC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Mobile-Friendly PWM/PFM Controller |
| 中文描述： | SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | QSOP-16 |
| 文件頁數： | 10/15頁 |
| 文件大小： | 537K |
| 代理商： | FAN5234QSC |
PRODUCT SPECIFICATION
FAN5234
10
REV. 1.0.10 5/3/04
Setting the Output Voltage
The internal reference is 0.9V. The output is divided down by
a voltage divider to the VSEN pin (for example, R1 and R2
in Figure 1). The output voltage therefore is:
To minimize noise pickup on this node, keep the resistor to
GND (R2) below 2K. We selected R2 at 1.82K. Then choose
R5:
Output Inductor Selection
The minimum practical output inductor value is the one that
keeps inductor current just on the boundary of continuous
conduction at some minimum load. The industry standard
practice is to choose the ripple current to be somewhere from
15% to 35% of the nominal current. At light load, the ripple
current also determines the point where the converter will
automatically switch to hysteretic mode of operation (I
MIN
)
to sustain high efficiency. The following equations help to
choose the proper value of the output filter inductor.
where
I is the inductor ripple current, which we will choose
for 20% of the full load current and
V
OUT
is the maximum
output ripple voltage allowed.
for this example we'll use:
V
IN
= 20V, V
OUT
= 1.8V
I = 20% * 3.5A = 0.7A
F
SW
= 300KHz.
therefore
L
≈
8
μ
H
Output Capacitor Selection
The output capacitor serves two major functions in a switch-
ing power supply. Along with the inductor it filters the
sequence of pulses produced by the switcher, and it supplies
the load transient currents. The output capacitor require-
ments are usually dictated by ESR, Inductor ripple current
(
I) and the allowable ripple voltage (
V).
For our example,
In addition, the capacitor's ESR must be low enough to allow
the converter to stay in regulation during a load step. The rip-
ple voltage due to ESR for the converter in Figure 1 is
100mV P-P. Some additional ripple will appear due to the
capacitance value itself:
which is only about 1.5mV for the converter in Figure 1 and
can be ignored.
The capacitor must also be rated to withstand the RMS cur-
rent which is approximately 0.3 X (
I), or about 210mA for
our example. High frequency decoupling capacitors should
be placed as close to the loads as physically possible.
Input Capacitor Selection
The input capacitor should be selected by its ripple current
rating. The input RMS current at maximum load current (I
L
)
is:
where the converter duty cycle;
, which for
the circuit in Figure 1, with V
IN
=6 calculates to:
Power MOSFET Selection
Losses in a MOSFET are the sum of its switching (P
SW
) and
conduction (P
COND
) losses.
In typical applications, the FAN5234 converter's output volt-
age is low with respect to its input voltage, therefore the
Lower MOSFET (Q2) is conducting the full load current for
most of the cycle. Q2 should be therefore be selected to min-
imize conduction losses, thereby selecting a MOSFET with
low R
DS(ON)
.
In contrast, the high-side MOSFET (Q1) has a much shorter
duty cycle, and it's conduction loss will therefore have less of
an impact. Q1, however, sees most of the switching losses,
so Q1's primary selection criteria should be gate charge.
High-Side Losses:
Figure 8 shows a MOSFET's switching interval, with the
upper graph being the voltage and current on the Drain to
Source and the lower graph detailing V
GS
vs. time with a
constant current charging the gate. The x-axis therefore is
also representative of gate charge (Q
G
) . C
ISS
= C
GD
+ C
GS
,
and it controls t1, t2, and t4 timing. C
GD
receives the current
from the gate driver during t3 (as V
DS
is falling). The gate
charge (Q
G
) parameters on the lower graph are either speci-
fied or can be derived from MOSFET datasheets.
R2
0.9V
V
--------------------------------
0.9V
–
R1
=
(9a)
R5
-1.82K
(
)
1.8V
0.9
0.9
–
(
)
1.82K
=
=
(9b)
I
2
I
MIN
–
V
ESR
------------------
=
=
(10)
L
V
F
SW
OUT
I
×
–
----------------V
V
V
IN
--------------
×
=
(11)
ESR
V
I
-------
<
(12)
ESR
MAX
(
)
V
I
-------
0.7A
142m
=
=
=
V
C
OUT
8
F
SW
×
--------------------I
=
(13)
I
RMS
I
L
D
D
2
–
=
(14)
D
V
V
IN
--------------
=
I
RMS
1.6A
=
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5234QSCX | Mobile-Friendly PWM/PFM Controller |
| FAN5234 | Terminal Block; Pitch Spacing:0.197"; Mounting Type:PC Board RoHS Compliant: Yes |
| FAN5235 | System Electronics Regulator for Mobile PCs |
| FAN5236MTC | Dual Mobile-Friendly DDR / Dual-output PWM Controller |
| FAN5236MTCX | Dual Mobile-Friendly DDR / Dual-output PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5234QSC_Q | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5234QSCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5235 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:System Electronics Regulator for Mobile PCs |
| FAN5235_CAB3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5235_CAB3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。