- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5240MTCX (FAIRCHILD SEMICONDUCTOR CORP) Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM PDF資料下載
參數資料
| 型號： | FAN5240MTCX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM |
| 中文描述： | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | MO-153AB, TSSOP-28 |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 447K |
| 代理商： | FAN5240MTCX |
FAN5240
PRODUCT SPECIFICATION
12
REV. 1.1.7 8/29/02
Figure 9. Compensation
This region is also associated with phase ‘bump’ or reduced
phase shift. The amount of phase shift reduction depends on
how wide the region of flat gain is and has a maximum value
of 90 degrees. To further simplify the converter compensa-
tion, the modulator gain is kept independent of the input
voltage variation by providing feed-forward of VIN to the
oscillator ramp.
The zero frequency, the amplifier high frequency gain and
the modulator gain are chosen to satisfy most typical appli-
cations. The crossover frequency will appear at the point
where the modulator attenuation equals the amplifier high
frequency gain. The only task that the system designer has to
complete is to specify the output filter capacitors to position
the load main pole somewhere within one decade lower than
the amplifier zero frequency. With this type of compensation
plenty of phase margin is easily achieved due to zero-pole
pair phase ‘boost’.
Conditional stability may occur only when the main load
pole is positioned too much to the left side on the frequency
axis due to excessive output filter capacitance. In this case,
the ESR zero placed within the 10kHz...50kHz range gives
some additional phase ‘boost’. Fortunately, there is an oppo-
site trend in mobile applications to keep the output capacitor
as small as possible.
Protection
The converter output is monitored and protected against
short circuit (over-current), and over-voltage conditions.
Over-Current sensing
(see Figure 10)
When the circuit's current limit signal (“ILIM det” as shown
in Figure 6) goes high, a pulse-skipping circuit is activated
and a 16-clock cycle counter is started. HDRV will be inhib-
ited as long as the sensed current is higher than the ILIM
value. This limits the current supplied by the DC input.
Figure 10. Over-current shut-down delay logic
If ILIM det goes high during counts 9-16 of the counter, the
overcurrent delay timer is started and the 16-clock counter
starts again. This timer delays the shut-down of the chip and
its time is a function of the value of C
DELAY
.
Over-current must detected at least once during the first 8
clock cycles and once during the 2
nd
8 clock cycles of the
16-cycle counter for the timer to continue timing. If the over-
current condition does not occur at least once per 8 clock
counts during any clock counter cycle while the timer is
high, the timer and the over-current detection circuit are
reset, preventing shutdown. The clock counter coutinues to
count and look for ILIM det pulses in this manner until
either:
1.
the IC is shut-down because the timer timed out:
If the timer pulse is allowed to finish by timing out, the
IC is shut-down and can only be restarted by removing
power or toggling the EN pin.
2.
ILIM det does not go high at least once per 8 clock
counts. In this case, the timer and over-current shutdown
logic are reset, and a chip shut-down is averted.
PGOOD will go LOW if the IC shuts down from over-
current.
Setting the Current Limit
ISNS is compared to the current established when a 0.9 V
internal reference drives the ILIM pin. The threshold is
determined at the point when the
. Since
therefore,
R1
F
P0
18
14
0
F
P
R2
+
–
C1
C2
V
IN
REF
Convete
EAOut
F
Z
Error Amp
Modulator
F
Z
2
1
---------------------
6 kHz
=
=
(9a)
F
P
2
2
---------------------
600 kHz
=
=
(9b)
Clock
Shut-down
RESET
16 Clock
Counter and
Logic
START
DELAY
Q TIMER
ILIM det. 1
ILIM det. 2
T
HOLDOFF
in mS
(
)
C
in nF
(
)
---------------------------------------
=
(10)
--------------
ILIM
--------------
>
ISNS
I
-------------------------------------------
R
R
SENSE
)
=
R
ILIM
LIMIT
--------------
8
-----------------------------------
R
DS ON
(
)
)
×
=
(11)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5240QSC | Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM |
| FAN5240QSCX | Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM |
| FAN5250 | Mobile Processor Core-Voltage Regulator |
| FAN5250QSC | Mobile Processor Core-Voltage Regulator |
| FAN5250QSCX | Mobile Processor Core-Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5240QSC | 功能描述:開關變換器、穩壓器與控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5240QSCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller Two Phase RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5242_AAB3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5242MTC | 功能描述:開關變換器、穩壓器與控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5242MTCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。