- 您現在的位置：買賣IC網 > PDF目錄375725 > FAN5609MTCX (FAIRCHILD SEMICONDUCTOR CORP) CLIPS PDF資料下載
參數資料
| 型號： | FAN5609MTCX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | CLIPS |
| 中文描述： | LED DISPLAY DRIVER, PDSO14 |
| 封裝： | TSSOP-14 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 112K |
| 代理商： | FAN5609MTCX |
PRODUCT SPECIFICATION
FAN5609
REV. 1.0.2 5/30/03
7
Digital Control with PWM
(Continued)
A and B are PWM.
I
LED
(Average) =
δ
x 20mA, where
δ
is Duty Cycle. (Note 3, 5)
B Input (PWM)
A Input (PWM)
s
1KHz
s
D 30%
1KHz
70%
Duty Cycle
70%
Duty Cycle
D 30%
s
0mA
OFF
ILED
I
LED
(Average)
= 0.3 x 20mA = 6mA
I
LED
(Average)
= 0.7 x 20mA = 14mA
Notes:
5. Proportionally select the duty cycle to achieve a typical LED current between 1mA to 19mA.
Application Information
Selecting Capacitors
It is important to select the appropriate capacitor types and
the values for use with the FAN5609. These capacitors
determine parameters such as power efficiency, maximum
sustainable load current by the charge pump, input and
output ripple and start-up time.
In order to reduce ripple, both C
ESR capacitor. Increasing the C
put ripple voltage. However this will increase the power-on
time. The C
IN
value controls input ripple. If necessary, this
ripple can be further reduced by powering the FAN5609
through a very small series inductor filter, as shown in Figure 3.
IN
OUT
and C
capacitor reduces the out-
OUT
should be low
Figure 3.
CAP1 and CAP2 control the current capability of the charge
pump and affect the overall efficiency of the system. A lower
value will improve efficiency, but it may limit the LED’s
currents at low input voltage. A capacitor of 100nF is opti-
mal for 4
×
20 mA load over the entire input voltage range of
2.7V to 4.2V. To save space and cost, and to increase effi-
ciency, this value may be reduced to 10nF for loads less than
4 x 7mA.
Pulse-Width-Modulated (PWM) Mode
Conversion errors are minimized and the best LED to LED
matching is achieved over the entire range of average current
settings, when PWM brightness control is used to modulate
the LED current between zero and the maximum value
(A=1, B=1).
PC Board Layout
For best performance, a solid ground plane is recommended
on the back side of the PCB. The ground tails of C
C
OUT
should be connected together close to the GND pin of
IC.
IN
and
100nH
0.1
μ
F
4.7
μ
F
Input
Power
Supply
V
IN
FAN5609
GND
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5610MPX | LED Driver for White, Blue or any Color LED |
| FAN5610 | LED Driver for White, Blue or any Color LED |
| FAN5611 | Low-Dropout LED Drivers for White, Blue or any Color LED |
| FAN5611S7X | Low-Dropout LED Drivers for White, Blue or any Color LED |
| FAN5612 | Low-Dropout LED Drivers for White, Blue or any Color LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5610 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:LED Driver for White, Blue or any Color LED |
| FAN5610_ACC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5610A WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5610MPX | 功能描述:LED照明驅動器 LED Driver all Colors RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| FAN5611 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Low-Dropout LED Drivers for White, Blue, or any Color LED |
發布緊急采購，3分鐘左右您將得到回復。