欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: FOD2743A
廠商: FAIRCHILD SEMICONDUCTOR CORP
元件分類: 光電耦合器
英文描述: OPTICALLY ISOLATED ERROR AMPLIFIER
中文描述: 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER
封裝: DIP-8
文件頁數: 10/15頁
文件大小: 619K
代理商: FOD2743A
4/8/04
Page 10 of 15
2004 Fairchild Semiconductor Corporation
OPTICALLY ISOLATED
ERROR AMPLIFIER
FOD2743A
FOD2743B
FOD2743C
The FOD2743
The FOD2743 is an optically isolated error amplifier. It incor-
porates three of the most common elements necessary to
make an isolated power supply, a reference voltage, an error
amplifier, and an optocoupler. It is functionally equivalent to
the popular KA431 shunt voltage regulator plus the CNY17F-X
optocoupler.
Powering the Secondary Side
The LED pin in the FOD2743 powers the secondary side, and
in particular provides the current to run the LED. The actual
structure of the FOD2743 dictates the minimum voltage that
can be applied to the LED pin: The error amplifier output has a
minimum of the reference voltage, and the LED is in series
with that. Minimum voltage applied to the LED pin is thus 2.5V
+ 1.2V = 3.7V. This voltage can be generated either directly
from the output of the converter, or else from a slaved second-
ary winding. The secondary winding will not affect regulation,
as the input to the FB pin may still be taken from the output
winding.
The LED pin needs to be fed through a current limiting resistor.
The value of the resistor sets the amount of current through
the LED, and thus must be carefully selected in conjunction
with the selection of the primary side resistor.
Feedback
Output voltage of a converter is determined by selecting a
resistor divider from the regulated output to the FB pin. The
FOD2743 attempts to regulate its FB pin to the reference
voltage, 2.5V. The ratio of the two resistors should thus be:
The absolute value of the top resistor is set by the input offset
current of 5.2μA. To achieve 0.5% accuracy, the resistance of
R
TOP
should be:
Compensation
The compensation pin of the FOD2743 provides the opportu-
nity for the designer to design the frequency response of the
converter. A compensation network may be placed between
the COMP pin and the FB pin. In typical low-bandwidth
systems, a 0.1μF capacitor may be used. For converters with
more stringent requirements, a network should be designed
based on measurements of the system’s loop. An excellent
reference for this process may be found in “Practical Design of
Power Supplies” by Ron Lenk, IEEE Press, 1998.
Secondary Ground
The GND pin should be connected to the secondary ground of
the converter.
No Connect Pins
The NC pins have no internal connection. They should not
have any connection to the secondary side, as this may
compromise the isolation structure.
Photo-Transistor
The Photo-transistor is the output of the FOD2743. In a normal
configuration the collector will be attached to a pull-up resistor
and the emitter grounded. There is no base connection neces-
sary.
The value of the pull-up resistor, and the current limiting resis-
tor feeding the LED, must be carefully selected to account for
voltage range accepted by the PWM IC, and for the variation in
current transfer ratio (CTR) of the opto-isolator itself.
Example:
The voltage feeding the LED pins is +12V, the
voltage feeding the collector pull-up is +10V, and the PWM
IC is the Fairchild FAN4803, which has a 5V reference. If we
select a 10k
resistor for the LED, the maximum current the
LED can see is (12V-4V) /10k
= 800μA. The CTR of the
opto-isolator is a minimum of 50%, so the minimum collector
current of the photo-transistor when the diode is full on is
400μA. The collector resistor must thus be such that:
select 20k
to allow some margin.
R
BOTTOM
R
V
REF
V
1
=
V
TOP
2.5
------R
1040
μ
A
>
5V
COLLECTOR
R
400
μ
A or R
COLLECTOR
12.5k
;
>
<
相關PDF資料
PDF描述
FOD2743B OPTICALLY ISOLATED ERROR AMPLIFIER
FOD2743C OPTICALLY ISOLATED ERROR AMPLIFIER
FOD816 4-Pin Phototransistor Optocouplers
FOD816300 4-Pin Phototransistor Optocouplers
FOD816300W 4-Pin Phototransistor Optocouplers
相關代理商/技術參數
參數描述
FOD2743A_08 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Optically Isolated Error Amplifier
FOD2743AS 功能描述:光隔離放大器 Error Amp Coupler Transistor Output RoHS:否 制造商:Avago Technologies 絕緣電壓:5000 Vrms 參考電壓: 電流傳遞比: 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
FOD2743ASD 功能描述:光隔離放大器 Error Amp Coupler Transistor Output RoHS:否 制造商:Avago Technologies 絕緣電壓:5000 Vrms 參考電壓: 電流傳遞比: 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
FOD2743ASDV 功能描述:光隔離放大器 Error Amp Coupler Transistor Output RoHS:否 制造商:Avago Technologies 絕緣電壓:5000 Vrms 參考電壓: 電流傳遞比: 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
FOD2743ASV 功能描述:光隔離放大器 Error Amp Coupler Transistor Output RoHS:否 制造商:Avago Technologies 絕緣電壓:5000 Vrms 參考電壓: 電流傳遞比: 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
主站蜘蛛池模板: 边坝县| 安塞县| 华蓥市| 阳泉市| 云阳县| 醴陵市| 奇台县| 梁平县| 永嘉县| 合水县| 青川县| 句容市| 宜宾市| 祁门县| 息烽县| 永新县| 武定县| 保德县| 吉水县| 怀集县| 元阳县| 铜川市| 宁晋县| 梨树县| 揭阳市| 色达县| 大厂| 永济市| 淄博市| 灌阳县| 绥宁县| 家居| 长乐市| 吉林市| 延川县| 诸暨市| 洛川县| 宁波市| 桓仁| 福清市| 皮山县|