- 您現在的位置：買賣IC網 > PDF目錄375932 > FSES0765RGWDTU (FAIRCHILD SEMICONDUCTOR CORP) Green Mode Fairchild Power Switch (FPS) for Green Mode Fairchild Power Switch (FPSTM) for PDF資料下載
參數資料
| 型號： | FSES0765RGWDTU |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Green Mode Fairchild Power Switch (FPS) for Green Mode Fairchild Power Switch (FPSTM) for |
| 中文描述： | 15 A SWITCHING REGULATOR, 130 kHz SWITCHING FREQ-MAX, PZFM6 |
| 封裝： | TO-220, 6 PIN |
| 文件頁數： | 11/18頁 |
| 文件大小： | 249K |
| 代理商： | FSES0765RGWDTU |
FSES0765RG
11
Functional Description
Startup
: In previous generations of Fairchild Power
Switches (FPS
TM
) the Vcc pin had an external start-up
resistor to the DC input voltage line. In this generation the
startup resistor is replaced by an internal high voltage current
source. At startup, an internal high voltage current source
supplies the internal bias and charges the external capacitor
(C
vcc
) that is connected to the Vcc pin as illustrated in figure
4. When Vcc reaches 12V, the FPS begins switching and the
internal high voltage current source is disabled. Then, the
FPS continues its normal switching operation and the power
is supplied from the auxiliary transformer winding unless
Vcc goes below the stop voltage of 9V.
1.
Figure 4. Internal Startup Circuit
2. Feedback Control
: FSES0765RG employs current mode
control, as shown in figure 5. An opto-coupler (such as the
H11A817A) and shunt regulator (such as the KA431) are
typically used to implement the feedback network.
Comparing the feedback voltage with the voltage across the
Rsense resistor plus an offset voltage makes it possible to
control the switching duty cycle. When the reference pin
voltage of the KA431 exceeds the internal reference voltage
of 2.5V, the H11A817A LED current increases, thus pulling
down the feedback voltage and reducing the duty cycle. This
event typically happens when the input voltage is increased
or the output load is decreased.
2.1 Pulse-by-pulse Current Limit
: Because current mode
control is employed, the peak current through the Sense FET
is limited by the inverting input of the PWM comparator
(Vfb*) as shown in figure 5. Assuming that the 0.9mA
current source flows only through the internal resistor (2.5R
+R= 2.8 k
Ω
), the cathode voltage of diode D2 is about 2.5V.
Since diode D1 is blocked when the feedback voltage (Vfb)
exceeds 2.5V, the maximum voltage of the cathode of D2 is
clamped at this voltage, thus clamping Vfb*. Therefore, the
peak value of the SenseFET current is limited.
2.2 Leading Edge Blanking (LEB)
: At the instant the
internal Sense FET is turned on, there usually exists a high
current spike through the Sense FET, caused by primary-side
capacitance and secondary-side rectifier reverse recovery.
Excessive voltage across the Rsense resistor would lead to
incorrect feedback operation in the current mode PWM
control. To counter this effect, the FPS employs a leading
edge blanking (LEB) circuit. This circuit inhibits the PWM
comparator for a short time (T
LEB
) after the Sense FET is
turned on.
Figure 5. Pulse Width Modulation (PWM) Circuit
3. Protection Circuits
: The FSES0765RG has several self
protective functions such as over load protection (OLP),
abnormal over current protection (AOCP), over voltage
protection (OVP) and thermal shutdown (TSD). Because
these protection circuits are fully integrated into the IC
without requiring external components, the reliability can be
improved without increasing cost. Once the fault condition
occurs, switching is terminated and the Sense FET remains
off. This causes Vcc to fall. When Vcc reaches the UVLO
stop voltage, 9V, the protection is reset and the internal high
voltage current source charges the Vcc capacitor via the Vstr
pin. When Vcc reaches the UVLO start voltage,12V, the FPS
resumes its normal operation. In this manner, the auto-restart
can alternately enable and disable the switching of the power
Sense FET until the fault condition is eliminated (see figure
6).
9V/12V
3
Vref
Internal
Bias
Vcc
6
Vstr
I
start
Vcc good
V
DC
C
Vcc
4
OSC
Vcc
Vref
I
delay
I
FB
V
SD
R
2.5R
Gate
driver
OLP
D1
D2
+
V
fb
*
-
Vfb
KA431
C
B
Vo
H11A817A
R
sense
SenseFET
相關PDF資料 |
PDF描述 |
|---|---|
| FSES0765RG | Green Mode Fairchild Power Switch (FPS) for Green Mode Fairchild Power Switch (FPSTM) for |
| FSF055D1 | 25A, 60V, 0.020 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSF055D | 25A, 60V, 0.020 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSF055R | 25A, 60V, 0.020 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSF055D3 | 25A, 60V, 0.020 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FSEZ1016A | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Primary-Side-Regulation PWM Integrated Power MOSFET |
| FSEZ1016A_10 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Primary-Side-Regulation PWM Integrated Power MOSFET |
| FSEZ1016AMY | 功能描述:初級與次級側 PWM 控制器 PSC PWM Controller w/MOSFET RoHS:否 制造商:ON Semiconductor 輸出端數量:1 開關頻率:250 KHz 工作電源電壓:- 0.3 V to + 28 V 最大工作溫度:+ 85 C 最小工作溫度:- 5 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Reel |
| FSEZ1016ANY | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FSEZ1016ASY | 制造商:Fairchild Semiconductor Corporation 功能描述:PRIMARY SIDE REGULATION PWM WITH POWER MOSFET INTEGRATED - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。