- 您現在的位置：買賣IC網 > PDF目錄385310 > GS1528ACKAE3 (Gennum Corporation) GS1528A / GS9068A HD-LINX-R II Multi-Rate Dual Slew-Rate Cable Driver PDF資料下載
參數資料
| 型號： | GS1528ACKAE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS1528A / GS9068A HD-LINX-R II Multi-Rate Dual Slew-Rate Cable Driver |
| 中文描述： | GS1528A / GS9068A的HD - LINX進程- R的第二多速率的雙擺率電纜驅動器 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 495K |
| 代理商： | GS1528ACKAE3 |
GS1528A / GS9068A Data Sheet
30953 - 4
January 2006
9 of 16
5. Detailed Description
5.1 Input Interfacing
S
DI/SDI are high impedance differential inputs. The equivalent input circuit is shown
in
Figure 4-1
.
Several conditions must be observed when interfacing to these inputs:
The differential input signal amplitude must be between 300 and 2000mVpp.
The common mode voltage range must be as specified in the
DC Electrical
Characteristics
table
.
For input trace lengths longer than approximately 1cm, the inputs should be
terminated as shown in the Typical Application Circuit.
The GS1528A/9068A inputs are self-biased, allowing for simple AC coupling to the
device. For serial digital video, a minimum capacitor value of 4.7μF should be used
to allow coupling of pathological test signals. A tantalum capacitor is
recommended.
SD/HD Input Pin (GS1528A only):
The GS1528A SDO rise and fall times can be set to comply with both SMPTE
259M/344M and SMPTE 292M. For all SMPTE 259M standards, or any data rate
that requires longer rise and fall time characteristics, the SD/HD pin must be set
HIGH by the application layer. For SMPTE 292M standards and signals which
require faster rise and fall times, this pin should be set LOW.
5.2 Output Interfacing
The GS1528A/9068A outputs are current mode, and will drive 800mV into a 75
Ω
load. These outputs are protected from accidental static damage with internal static
protection diodes.
The SMPTE 292M, SMPTE 344M and SMPTE 259M standards require that the
output of a cable driver have a source impedance of 75
Ω
and a return loss of at
least 15dB between 5MHz and 1.485GHz.
In order for an SDI output circuit using the GS1528A/9068A to meet this
specification, the output application circuit shown in
Section 6.2
is recommended.
The value of L
COMP
will vary depending on the PCB layout, with a typical value of
5.6nH
. A 4.7μF capacitor is used for AC coupling the output of the device. This
value is chosen to ensure that pathological signals can be coupled without a
significant DC component occurring. Please see
Section 6.0
for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| GS9068A | GS1528A / GS9068A HD-LINX-R II Multi-Rate Dual Slew-Rate Cable Driver |
| GS9068ACKAE3 | GS1528A / GS9068A HD-LINX-R II Multi-Rate Dual Slew-Rate Cable Driver |
| GS1532-CF | GS1532 HD-LINX-TM II Multi-Rate Serializer |
| GS1532-CFE3 | GS1532 HD-LINX-TM II Multi-Rate Serializer |
| GS1535-CFU | GS1535 HD-LINX II-TM Multi-Rate SDI Automatic Reclocker |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS1528ACTAE3 | 制造商:Semtech Corporation 功能描述:Cable Driver 8-Pin SOIC T/R 制造商:Semtech Corporation 功能描述:HD/SD/ASI Cable Driver |
| GS1528ACTAE3D | 制造商:Semtech Corporation 功能描述:HS/SD/ASI Cable Driver |
| GS1528B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Multi-Rate Dual Slew-Rate Cable Driver |
| GS1528BCKAE3 | 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:* 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| GS1528BCTAE3 | 制造商:Semtech Corporation 功能描述:Cable Driver 8-Pin SOIC 制造商:Semtech Corporation 功能描述:HD/SD/ASI Cable Driver |
發布緊急采購，3分鐘左右您將得到回復。