- 您現在的位置：買賣IC網 > PDF目錄385332 > GS8644ZV18E-150 (GSI TECHNOLOGY) 72Mb Pipelined and Flow Through Synchronous NBT SRAM PDF資料下載
參數資料
| 型號： | GS8644ZV18E-150 |
| 廠商： | GSI TECHNOLOGY |
| 元件分類： | DRAM |
| 英文描述： | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| 中文描述： | 4M X 18 ZBT SRAM, 7.5 ns, PBGA165 |
| 封裝： | 15 X 17 MM, 1 MM PITCH, FBGA-165 |
| 文件頁數： | 28/37頁 |
| 文件大小： | 776K |
| 代理商： | GS8644ZV18E-150 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Product Preview
GS8644ZV18(B/E)/GS8644ZV36(B/E)/GS8644ZV72(C)
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.03 11/2004
28/37
2003, GSI Technology
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
RFU
These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| GS8644ZV18E-150I | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-166 | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-166I | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-200 | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-200I | 72Mb Pipelined and Flow Through Synchronous NBT SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS8644ZV18E-150I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-166 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-166I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-200 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM |
| GS8644ZV18E-200I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM |
發布緊急采購，3分鐘左右您將得到回復。