- 您現在的位置：買賣IC網 > PDF目錄385338 > GS8662S08E-250 (GSI TECHNOLOGY) 72Mb Burst of 2 DDR SigmaSIO-II SRAM PDF資料下載
參數資料
| 型號： | GS8662S08E-250 |
| 廠商： | GSI TECHNOLOGY |
| 元件分類： | DRAM |
| 英文描述： | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| 中文描述： | 8M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| 封裝： | 15 X 17 MM, 1 MM PITCH, MO-216CAB-1, FPBGA-165 |
| 文件頁數： | 8/37頁 |
| 文件大?。?/td> | 960K |
| 代理商： | GS8662S08E-250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Preliminary
GS8662S08/09/18/36E-333/300/250/200/167
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.01 9/2005
8/37
2005, GSI Technology
Power-Up Sequence for SigmaQuad-II SRAMs
SigmaQuad-II SRAMs must be powered-up in a specific sequence in order to avoid undefined operations.
Power-Up Sequence
1. Power-up and maintain Doff at low state.
1a.
Apply V
DD
.
1b. Apply V
DDQ
.
1c. Apply V
REF
(may also be applied at the same time as V
DDQ
).
2. After power is achieved and clocks (K, K, C, C) are stablized, change Doff to high.
3. An additional 1024 clock cycles are required to lock the DLL after it has been enabled.
Note:
If you want to tie Doff high with an unstable clock, you must stop the clock for a minimum of 30 seconds to reset the DLL after the clocks become
stablized.
DLL Constraints
The DLL synchronizes to either K or C clock. These clocks should have low phase jitter (t
KCVar
on page 21).
The DLL cannot operate at a frequency lower than 119 MHz.
If the incoming clock is not stablized when DLL is enabled, the DLL may lock on the wrong frequency and cause undefined errors or failures during
the initial stage.
Power-Up Sequence (Doff controlled)
Power UP Interval
Unstable Clocking Interval
DLL Locking Interval (1024 Cycles)
Normal Operation
K
K
V
DD
V
DDQ
V
REF
Doff
Power-Up Sequence (Doff tied High)
Power UP Interval
Unstable Clocking Interval
Stop Clock Interval
30ns Min
DLL Locking Interval (1024 Cycles)
Normal Operation
K
K
V
DD
V
DDQ
V
REF
Doff
Note:
If the frequency is changed, DLL reset is required. After reset, a minimum of 1024 cycles is required for DLL lock.
相關PDF資料 |
PDF描述 |
|---|---|
| GS8662S08E-250I | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-300 | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-300I | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-333 | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08GE-167 | 72Mb Burst of 2 DDR SigmaSIO-II SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS8662S08E-250I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-300 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-300I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-333 | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Burst of 2 DDR SigmaSIO-II SRAM |
| GS8662S08E-333I | 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Burst of 2 DDR SigmaSIO-II SRAM |
發布緊急采購，3分鐘左右您將得到回復。