欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: GS88236AB-225
廠商: GSI TECHNOLOGY
元件分類: DRAM
英文描述: 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
中文描述: 256K X 36 CACHE SRAM, 6 ns, PBGA119
封裝: PLASTIC, BGA-119
文件頁數: 28/38頁
文件大小: 744K
代理商: GS88236AB-225
GS88218/36AB/D-250/225/200/166/150/133
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.04 11/2004
28/38
2001, GSI Technology
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
RFU
These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction.
相關PDF資料
PDF描述
GS88236AB-225I 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-250 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-250I 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AD-133 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AD-133I 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
相關代理商/技術參數
參數描述
GS88236CB-200 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V/3.3V 9MBIT 256KX36 6.5NS/3NS 119FPBGA - Trays
GS88236CB-200I 制造商:GSI Technology 功能描述:256K X 36 (9 MEG) SYNCH BURST , SCD, JTAG, FLEXDRIVE - Trays
GS88236CB-200IV 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V/2.5V 9MBIT 256KX36 6.5NS/3NS 119FPBGA - Trays
GS88236CB-250 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V/3.3V 9MBIT 256KX36 5.5NS/2.5NS 119FPBGA - Trays
GS88236CD-200 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V/3.3V 9MBIT 256KX36 6.5NS/3NS 165FPBGA - Trays
主站蜘蛛池模板: 固镇县| 文化| 双峰县| 资源县| 宜城市| 台州市| 辽阳市| 安平县| 大姚县| 开江县| 全椒县| 武清区| 武穴市| 高邮市| 大方县| 五河县| 陆河县| 久治县| 永兴县| 门头沟区| 章丘市| 黄陵县| 南开区| 霍林郭勒市| 启东市| 新干县| 乐山市| 美姑县| 元谋县| 宜宾市| 沂南县| 长沙市| 永丰县| 山西省| 绥阳县| 浮梁县| 唐山市| 叶城县| 四会市| 巴林左旗| 康马县|