欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HA4244
廠商: Intersil Corporation
英文描述: 480MHz, 1 x 1 Video Crosspoint Switch with Synchronous Enable
中文描述: 480MHz,1 × 1視頻交叉點開關同步啟用
文件頁數: 4/6頁
文件大小: 145K
代理商: HA4244
4
Application Information
General
The HA4244 is a synchronous 1 x 1 crosspoint switch that is
ideal for the matrix element in small, high input-to-output
isolation switchers and routers. The HA4244’s low input
capacitance and high input resistance provide excellent
video terminations when used with an external 75
resistor.
This crosspoint contains no feedback or gain setting
resistors, so the output is a true high impedance load when
the IC is disabled (EN = 0).
Synchronizing Latches
The HA4244 contains two latches which gate the EN input,
thereby allowing all the crosspoints in a matrix to switch
states synchronously. The latches also allow the EN input to
be changed without affecting the current state of the
HA4244. Thus, the next channel switch can be set up, and
isn’t acted upon until the next rising CLK edge. As long as
the EN signals meet a setup and hold time relative to the
rising CLK edge, all of the HA4244s will assume their new
state at the same time.
Power-Up Disable Function
The double latched EN signal, and single CLK input prevent
the user from controlling the crosspoint state at power-up.
To rectify this situation, the HA4244 incorporates power-up
circuitry to ensure that the crosspoint powers up in the
disabled state. Disabling the HA4244 prevents bus
contention between multiplexed outputs, and minimizes the
switching matrix supply current during power-up. Consider,
for example, a matrix of 625 crosspoints that power-up
randomly. If 50% of them power-up enabled, the required
matrix supply current is 3.3A (313 x 10.5mA), neglecting
output current. If HA4244s are utilized the power-up current
is reduced to 0.125A (625 x 200
μ
A).
Frequency Response
Most applications utilizing the HA4244 require a series
output resistor, R
S
, to tune the response for the specific load
capacitance, C
L
, driven. Bandwidth and slew rate degrade
as C
L
increases (as shown in the Electrical Specification
table), so give careful consideration to component
placement to minimize trace length. As an example, -3dB
bandwidth decreases to 160MHz for C
L
= 100pF, R
S
= 0
.
In big matrix configurations where C
L
is large, better
frequency response is obtained by cascading two levels of
crosspoints in the case of multiplexed outputs, or distributing
the load between two drivers if C
L
is due to bussing and
subsequent stage input capacitance.
Control Signals
EN - The ENABLE input is a TTL/CMOS compatible, active
high input. When driven low this input forces the output to a
true high impedance state and reduces the power
dissipation by two orders of magnitude.
CLK - An active high, TTL/CMOS compatible input that
controls the synchronizing latches. When CLK transistions
low, the current state of the EN input is latched in the IC.
This allows the EN input to be changed to the value
correspending to the next channel switch, without affecting
the HA4244’s current state. The HA4244 assumes the new
state on the next rising edge of CLK.
Power Up Considerations
No signals should be applied to the digital inputs before the
power supplies are activated. Latch-up may occur if the
inputs are driven at the time of power up. To prevent latch-
up, the input currents during power up must not exceed the
values listed in the Absolute Maximum Ratings.
Harris’ Crosspoint Family
Harris offers a variety of 1 x 1 and 4 x 1 crosspoint switches. In
addition to the HA4244, the 1 x 1 family includes the HA4600,
which is an essentially similar device but without the
synchronizing latches, and the HA4201 asynchronous
crosspoint with a Tally output (enable indicator). The 4 x 1
family is comprised of the HA4314, HA4404, and HA4344. The
HA4314 is a 14 lead basic 4 x 1 crosspoint. The HA4404 is a 16
lead device with Tally outputs to indicate the selected channel.
The HA4344 is a 16 lead crosspoint with synchronized control
lines (A0, A1, CS). With synchronization, the control information
for the next channel switch can be loaded into the crosspoint
without affecting the current state. On a subsequent clock edge
the stored control state effects the desired channel switch.
HA4244
相關PDF資料
PDF描述
HA4244CB 480MHz, 1 x 1 Video Crosspoint Switch with Synchronous Enable
HA4344 350MHz, 4 x 1 Video Crosspoint Switch with Synchronous Controls
HA4344BCB 350MHz, 4 x 1 Video Crosspoint Switch with Synchronous Controls
HA4344BCB96 350MHz, 4 x 1 Video Crosspoint Switch with Synchronous Controls
HA457CM 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch
相關代理商/技術參數
參數描述
HA4244CB 制造商:Rochester Electronics LLC 功能描述:- Bulk
HA4244CB WAF 制造商:Harris Corporation 功能描述:
HA4-2510-2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
HA4-2512-2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
HA4-2520-2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
主站蜘蛛池模板: 麟游县| 玛曲县| 金川县| 尤溪县| 泸溪县| 田阳县| 东源县| 西林县| 射阳县| 格尔木市| 南陵县| 虎林市| 宾川县| 新田县| 静海县| 盐亭县| 临夏县| 宕昌县| 夏邑县| 溧阳市| 荆门市| 建昌县| 百色市| 长子县| 齐河县| 宝鸡市| 章丘市| 双流县| 康马县| 浮山县| 峡江县| 枣庄市| 剑河县| 鹤庆县| 南投市| 疏附县| 永靖县| 郓城县| 呼伦贝尔市| 平和县| 陵水|