欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HC5523
廠商: Intersil Corporation
英文描述: LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby
中文描述: LSSGR/TR57文書主任/河套低功耗待機載波用戶接口
文件頁數: 9/18頁
文件大小: 176K
代理商: HC5523
64
The value of R
SG
should be calculated to allow maximum
loop length operation. This requires that the saturation guard
reference voltage be set as high as possible without clipping
the incoming or outgoing VF signal. A voltage margin of -4V
on tip and -4V on ring, for a total of -8V margin, is
recommended as a general guideline. The value of R
SG
is
calculated using Equation 6:
where:
V
BAT
= Battery voltage.
V
MAR
= Voltage Margin. Recommended value of -8V to
allow a maximum overload level of 3.1V peak.
For on-hook transmission R
L
=
, Equation 6 reduces to:
5
BAT
SLIC in the Standby Mode
Overall system power is saved by configuring the SLIC in the
standby state when not in use. In the standby state the tip and
ringamplifiersaredisabledandinternalresistorsareconnected
between tip to ground and ring to V
BAT
. This connection
enables a loop current to flow when the phone goes off-hook.
The loop current detector then detects this current and the
SLIC is configured in the active mode for voice transmission.
The loop current in standby state is calculated as follows:
where:
I
L
= Loop current in the standby state.
R
L
= Loop resistance.
V
BAT
= Battery voltage.
(AC) Transmission Path
SLIC in the Active Mode
Figure 16 shows a simplified AC transmission model. Circuit
analysis yields the following design equations:
where:
V
TR
= Is the AC metallic voltage between tip and ring,
including the voltage drop across the fuse resistors R
F
.
V
TX
= Is the AC metallic voltage. Either at the ground
referenced 4-wire side or the SLIC tip and ring terminals.
I
M
= Is the AC metallic current.
R
F
= Is a fuse resistor.
Z
T
= Is used to set the SLIC’s 2-wire impedance.
V
RX
= Is the analog ground referenced receive signal.
Z
RX
= Is used to set the 4-wire to 2-wire gain.
E
G
= Is the AC open circuit voltage.
Z
L
= Is the line impedance.
(AC) 2-Wire Impedance
The AC 2-wire impedance (Z
TR
) is the impedance looking
into the SLIC, including the fuse resistors, and is calculated
as follows:
Let V
RX
= 0. Then from Equation 10
RSG
---------------------------------------------
VBAT
VMAR
(
)
1
)
+
16.66V
×
----------------------------------------------------------------------------------------+
17300
=
(EQ. 6)
R
SG
MAR
------------------–
17300
=
(EQ. 7)
I
L
V
L
3V
---------+
(EQ. 8)
V
TR
V
TX
I
M
2R
F
+
=
(EQ. 9)
V
T
----------
V
RX
-----------
+
I
------------
=
(EQ. 10)
V
TR
E
G
I
M
Z
L
=
(EQ. 11)
V
TX
RSN
TIP
RING
I
M
1000
Z
TR
V
TR
E
G
-
V
TX
I
M
V
TX
Z
RX
1
HC5523
R
F
R
F
A = 4
+
-
+
-
+
+
-
Z
T
+
-
V
RX
+
-
A = 250
A = 250
I
M
Z
L
FIGURE 16. SIMPLIFIED AC TRANSMISSION CIRCUIT
V
TX
Z
T
I
------------
=
(EQ. 12)
HC5523
相關PDF資料
PDF描述
HC5523IM LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby
HC5523IP LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby
HC5526CM ITU CO/PABX SLIC with Low Power Standby
HC5526CP ITU CO/PABX SLIC with Low Power Standby
HC5526IM ITU CO/PABX SLIC with Low Power Standby
相關代理商/技術參數
參數描述
HC5523_03 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby
HC5523IM 制造商:Rochester Electronics LLC 功能描述:DLC/FITL SLIC,58DB LONG BAL,28PLCC,INDUS - Bulk
HC5523IMR4722 制造商:Rochester Electronics LLC 功能描述:- Bulk
HC5523IMX6176C 制造商:Rochester Electronics LLC 功能描述:- Bulk
HC5523IP 制造商:Rochester Electronics LLC 功能描述:- Bulk
主站蜘蛛池模板: 含山县| 利津县| 大庆市| 虎林市| 湖南省| 中卫市| 陆河县| 卫辉市| 邯郸市| 合水县| 专栏| 裕民县| 宝兴县| 武安市| 武穴市| 晋州市| 龙川县| 称多县| 东兴市| 台北县| 黔东| 上犹县| 台前县| 巧家县| 沧源| 司法| 克东县| 杭锦旗| 九江市| 即墨市| 黑龙江省| 陆川县| 颍上县| 南昌县| 营口市| 左贡县| 博罗县| 东港市| 平远县| 霍州市| 孝昌县|