- 您現在的位置：買賣IC網 > PDF目錄371820 > HIP1013CB-T (INTERSIL CORP) Low Cost Dual Power Distribution Controller PDF資料下載
參數資料
| 型號： | HIP1013CB-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Low Cost Dual Power Distribution Controller |
| 中文描述： | DUAL SWITCHING CONTROLLER, PDSO14 |
| 封裝： | PLASTIC, MS-012AB, SOIC-14 |
| 文件頁數： | 1/7頁 |
| 文件大小： | 51K |
| 代理商： | HIP1013CB-T |
2-406
HIP1013
Low Cost Dual Power Distribution
Controller
The HIP1013 is a low cost HOT SWAP dual supply power
distribution controller. Two external N-Channel MOSFETs
are driven to distribute power while providing load fault
isolation. At turn-on, the gate of each external N-Channel
MOSFET is charged with a 10
μ
A current source. Capacitors
on each gate (see the Typical Application Diagram), create a
programmable ramp (soft turn-on) to control inrush currents.
A built in charge pump supplies the gate drive for the 12V
supply N-Channel MOSFET switch.
Over current protection is facilitated by two external current
sense resistors. When the current through either resistor
exceeds the user programmed value the N-Channel
MOSFETs are latched off by the HIP1013. The controller is
reset by a rising edge on either PWRON pin.
Choosing the voltage selection mode the HIP1013 controls
either +12V/5V or +3.3V/+5V supplies.
Although pin compatible with the HIP1012 device, the
HIP1013 does not offer current regulation during an
OC event.
Features
HOT SWAP Dual Power Distribution Control for +5V and
+12V or +5V and +3.3V
Provides Fault Isolation
Charge Pump Allows the Use of N-Channel MOSFETs
Redundant Power On Controls
Power Good and Over Current Latch Indicators
Adjustable Turn-On Ramp
Protection During Turn-On
Applications
Power Distribution Control
Hot Plug Components
Pinout
HIP1013 (SOIC)
TOP VIEW
Typical Application Diagram
Ordering Information
PART
NUMBER
TEMP. RANGE
(
o
C)
PACKAGE
PKG. NO.
HIP1013CB
-0 to 70
14 Ld SOIC
M14.15
HIP1013CB-T
-0 to 70
14 Ld SOIC
Tape and Reel
M14.15
3/12VS
3/12VG
V
DD
PWRON2
5VG
5VS
3/12VISEN
GND
C
PUMP
NC
R
ILIM
PGOOD
5VISEN
MODE/
PWRON1
1
2
3
4
5
6
7
14
13
12
11
10
9
8
3/12VS
3/12VG
V
DD
M/PON1
PWRON2
5VG
5VS
PGOOD
3/12VISEN
GND
NC
R
ILIM
C
PUMP
5ISEN
HIP1013
12V
R
LOAD
R
ILIM
C
PUMP
R
SENSE
5V
R
LOAD
R
SENSE
5V
V
DD
C
GATE
C
GATE
POWER ON
INPUTS
Data Sheet
May 1999
File Number
4516.2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Hot Plug is a trademark of Core International, Inc.
http://www.intersil.com or 407-727-9207
|
Copyright
Intersil Corporation 1999
相關PDF資料 |
PDF描述 |
|---|---|
| HIP1013 | Dual Power Distribution Controller(雙電源分配控制器) |
| HIP1013CB | 5000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| HIP1015CB-T | Power Distribution Controllers |
| HIP1015CB | Power Distribution Controllers |
| HIP1015 | Power Distribution Controllers(電源分配控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1013CBZA | 功能描述:熱插拔功率分布 W/ANNEAL DUAL PWR DISTRIBUTION CONTRLR RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1013CBZA-T | 功能描述:熱插拔功率分布 W/ANNEAL PWR DIST TRLR W/OUT CURRE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1013EVAL1 | 功能描述:電源管理IC開發工具 GENERIC DL PWR DIST CNTRLR EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP1013EVAL2 | 功能描述:電源管理IC開發工具 GENERIC HIP1013 RAID EVALUATION BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP1015 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Power Distribution Controllers |
發布緊急采購，3分鐘左右您將得到回復。