- 您現在的位置：買賣IC網 > PDF目錄385382 > HIP6311ACBZA (INTERSIL CORP) XCV150-5BGG352I - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | HIP6311ACBZA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | XCV150-5BGG352I - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | LEAD FREE, PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 449K |
| 代理商： | HIP6311ACBZA |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
7
Operation
Figure 1 shows a simplified diagram of the voltage regulation
and current control loops. Both voltage and current feedback
are used to precisely regulate voltage and tightly control
output currents, I
L1
and I
L2
, of the two power channels. The
voltage loop comprises the Error Amplifier, Comparators,
gate drivers and output MOSFETS. The Error Amplifier is
essentially connected as a voltage follower that has as an
input, the Programmable Reference DAC and an output that
is the CORE voltage.
Voltage Loop
Feedback from the CORE voltage is applied via resistor R
IN
to the inverting input of the Error Amplifier. This signal can
drive the Error Amplifier output either high or low, depending
upon the CORE voltage. Low CORE voltage makes the
amplifier output move towards a higher output voltage level.
Amplifier output voltage is applied to the positive inputs of
the Comparators via the Correction summing networks. Out-
of-phase sawtooth signals are applied to the two
Comparators inverting inputs. Increasing Error Amplifier
voltage results in increased Comparator output duty cycle.
This increased duty cycle signal is passed through the PWM
CIRCUIT with no phase reversal and on to the HIP6601,
again with no phase reversal for gate drive to the upper
MOSFETs, Q1 and Q3. Increased duty cycle or ON time for
the MOSFET transistors results in increased output voltage
to compensate for the low output voltage sensed.
Current Loop
The current control loop works in a similar fashion to the
voltage control loop, but with current control information
applied individually to each channel’s Comparator. The
information used for this control is the voltage that is
developed across r
DS(ON)
of each lower MOSFET, Q2 and
Q4, when they are conducting. A single resistor converts and
scales the voltage across the MOSFETs to a current that is
applied to the Current Sensing circuit within the HIP6311A.
Output from these sensing circuits is applied to the current
averaging circuit. Each PWM channel receives the difference
current signal from the summing circuit that compares the
average sensed current to the individual channel current.
When a power channel’s current is greater than the average
FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF THE HIP6311A VOLTAGE AND CURRENT CONTROL LOOPS FOR A TWO POWER
CHANNEL REGULATOR
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
+
R
ISEN1
+
CORRECTION
ERROR
AMPLIFIER
FB
REFERENCE
DAC
I
SEN1
R
IN
V
CORE
Q3
Q4
L
02
PHASE
PWM1
I
L2
HIP6311A
C
OUT
R
LOAD
V
IN
HIP6601
-
Q1
Q2
L
01
PHASE
I
L1
V
IN
HIP6601
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
CORRECTION
PWM2
-
I AVERAGE
+
+
+
-
PROGRAMMABLE
R
ISEN2
I
SEN2
-
-
-
-
+
+
CURRENT
AVERAGING
∑
∑
∑
∑
HIP6311A
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6311ACBZA-T | 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HIP6311ACB-T | Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6502EVAL1 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6502 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6502CB | Multiple Linear Power Controller with ACPI Control Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6311ACBZA-T | 功能描述:電流型 PWM 控制器 W/ANNEAL C4AM MULTI- PHS CONTR 5% AC RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| HIP6311ACBZ-T | 功能描述:電流型 PWM 控制器 C4AM MULTI-PHS CONTR VID LVLS 5% AC RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| HIP6311CB | 功能描述:IC REG CTRLR BUCK PWM 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| HIP6311CB-T | 功能描述:IC REG CTRLR BUCK PWM 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| HIP6311CBZ | 功能描述:電流型 PWM 控制器 2-4 PHS SYNCH BUCK CNTRLR 0 8%F RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。