- 您現在的位置：買賣IC網 > PDF目錄385382 > HIP6503CB (INTERSIL CORP) Circular Connector; No. of Contacts:37; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:15-35 PDF資料下載
參數資料
| 型號： | HIP6503CB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Circular Connector; No. of Contacts:37; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:15-35 |
| 中文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 151K |
| 代理商： | HIP6503CB |
8
Not shown in these diagrams is the deglitching feature used
to protect against false sleep state tripping. Both S3 and S5
pins are protected against noise by a 2
μ
s filter (typically 1 -
4
μ
s). This feature is useful in noisy computer environments if
the control signals have to travel over significant distances.
Additionally, the S3 pin features a 200
μ
s delay in
transitioning to sleep states. Once the S3 pin goes low, an
internal timer is activated. At the end of the 200
μ
s interval, if
the S5 pin is low, the HIP6503 switches into S5 sleep state; if
the S5 pin is high, the HIP6503 goes into S3 sleep state.
Soft-Start Circuit
SOFT-START INTO SLEEP STATES (S3, S4/S5)
The 5VSB POR function initiates the soft-start sequence. An
internal 10
μ
A current source charges an external capacitor.
The error amplifiers reference inputs are clamped to a level
proportional to the SS (soft-start) pin voltage. As the SS pin
voltage slews from about 1.25V to 2.5V, the input clamp
allows a rapid and controlled output voltage rise.
Figure 7 shows the soft-start sequence for the typical
application start-up in sleep state with all output voltages
enabled. At time T0 5VSB (bias) is applied to the circuit. At
time T1 the 5VSB surpasses POR level. An internal fast
charge circuit quickly raises the SS capacitor voltage to
approximately 1V, then the 10
μ
A current source continues
the charging. The soft-start capacitor voltage reaches
approximately 1.25V at time T2, at which point the
3.3V
DUAL
/3.3V
SB
and 1.8V
SB
error amplifiers’ reference
inputs start their transition, resulting in the output voltages
ramping up proportionally. The ramp-up continues until time
T3 when the two voltages reach the set value. As the soft-
start capacitor voltage reaches approximately 2.75V, the
under-voltage monitoring circuit of this output is activated
and the soft-start capacitor is quickly discharged to
approximately 1.25V. Following the 3ms (typical) time-out
between T3 and T4, the MSEL and EN5VDL selections are
latched in, and the soft-start capacitor commences a second
ramp-up designed to smoothly bring up the remainder of the
voltages required by the system. At time T5 all voltages are
within regulation limits, and as the SS voltage reaches
2.75V, all the remaining UV monitors are activated and the
SS capacitor is quickly discharged to 1.25V, where it
remains until the next transition. As the 2.5V
CLK
output is
only active while in an active state, it does not come up, but
FIGURE 5. 5V
DUAL
TIMING DIAGRAM FOR EN5VDL = 0;
3V
DUAL
/3V
SB
5VSB
3.3V,
S3
S5
5VDLSB
DLA
3V3DLSB
3V3DL
5VDL
5V, 12V
FIGURE 6. 2.5V
MEM
, 3.3V
MEM
, AND 2.5V
CLK
TIMING DIAGRAM
5VSB
3.3V,
S3
S5
DRV2
VSEN 2
DEVICES
VSEN2
INTERNAL
VCLK
DLA
VSEN1
5V, 12V
FIGURE 7. SOFT-START INTERVAL IN A SLEEP STATE
(ALL OUTPUTS ENABLED)
0V
0V
TIME
SOFT-START
(1V/DIV)
OUTPUT
VOLTAGES
(1V/DIV)
V
OUT1
(1.8V
SB
)
V
OUT3
(3.3V
DUAL
/3.3V
SB
)
V
OUT2
(2.5V
MEM
)
V
OUT5
(5V
DUAL
)
T1 T2
T3
T0
5VSB
(1V/DIV)
T5
T4
V
OUT4
(2.5V
CLK
)
HIP6503
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6503 | Multiple Linear Power Controller with ACPI Control Interface(集成了多個線性電源控制器的芯片（ACPI控制接口）) |
| HIP6602ACB | FPGA 1600000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP6602ACR | FPGA 1600000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP6602ACR-T | FPGA 1600000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP6602ACB-T | Dual Channel Synchronous Rectified Buck MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6503CBZ | 功能描述:PMIC 解決方案 W/ANNEAL ACPI PWR MANAGEMNT CIRCUIT RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| HIP6503CBZ-T | 功能描述:PMIC 解決方案 W/ANNEAL ACPI PWR MG T CIRCUIT 20LD RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| HIP6503CR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| HIP6503EVAL1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multiple Linear Power Controller with ACPI Control Interface |
| HIP6521 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:PWM and Triple Linear Power Controller |
發布緊急采購，3分鐘左右您將得到回復。