- 您現在的位置：買賣IC網 > PDF目錄385388 > HMS81004E (Hynix Semiconductor Inc.) HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS PDF資料下載
參數資料
| 型號： | HMS81004E |
| 廠商： | Hynix Semiconductor Inc. |
| 元件分類： | 8位微控制器 |
| 英文描述： | HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| 中文描述： | Hynix半導體公司的8位單芯片微控制器 |
| 文件頁數： | 54/77頁 |
| 文件大小： | 1112K |
| 代理商： | HMS81004E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
HMS81004E/08E/16E/24E/32E
JUNE 2001 Ver 1.00
51
Figure 14-4 Timing chart of Interrupt Acceptance and Interrupt Return Instruction
A interrupt request is not accepted until the I-flag is set to “1”
even if a requested interrupt has higher priority than that of the
current interrupt being serviced.
When nested interrupt service is required, the I-flag should be set
to “1” by “EI” instruction in the interrupt service program. In this
case, acceptable interrupt sources are selectively enabled by the
individual interrupt enable flags.
Saving/Restoring General-purpose Register
During interrupt acceptance processing, the program counter and
the program status word are automatically saved on the stack, but
accumulator and other registers are not saved itself. These regis-
ters are saved by the software if necessary. Also, when multiple
interrupt services are nested, it is necessary to avoid using the
same data memory area for saving registers.
The following method is used to save/restore the general-purpose
registers.
Example: Register save using push and pop instructions
General-purpose register save/restore using push and pop instruc-
tions;
V.L.
System clock
Address Bus
PC
SP
SP-1
SP-2
V.H.
New PC
V.L.
Data Bus
Not used
PCH
PCL
PSW
ADL
OP code
ADH
Instruction Fetch
Internal Read
Internal Write
Interrupt Processing Step
Interrupt Service Task
V.L. and V.H. are vector addresses.
ADL and ADH are start addresses of interrupt service routine as vector contents.
External Interrupt1
Vector Table Address
012
H
0E3
H
0FFF8
H
0FFF9
H
0E
H
2E
H
0E312
H
0E313
H
Entry Address
Correspondence between vector table address for Exteranl Interrupt1
and the entry address of the interrupt service program.
INTxx:
PUSH
PUSH
PUSH
A
X
Y
;SAVE ACC.
;SAVE X REG.
;SAVE Y REG.
interrupt processing
POP
POP
POP
RETI
Y
X
A
;RESTORE Y REG.
;RESTORE X REG.
;RESTORE ACC.
;RETURN
main task
interrupt
service task
saving
registers
restoring
registers
acceptance of
interrupt
interrupt return
相關PDF資料 |
PDF描述 |
|---|---|
| HMS81008E | HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81016E | HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81024E | HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81032E | HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81C43XX | CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER FOR TELEVISION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMS81008 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REMOTE CONTROLLER |
| HMS81008E | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81016 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REMOTE CONTROLLER |
| HMS81016E | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| HMS81020ET | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REMOTE CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。