欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HMS87C1304A
廠商: Hynix Semiconductor Inc.
英文描述: CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
中文描述: CMOS單芯片8位微控制器
文件頁數: 57/70頁
文件大小: 977K
代理商: HMS87C1304A
HYUNDAI MicroElectronics
HMS87C1304A/HMS87C1302A
Jan. 2001
Preliminary
57
of the STOP feature. This point should be little current
flows when the input level is stable at the power voltage
level (V
DD
/V
SS
), however, when the input level gets high-
er than the power voltage level (by approximately 0.3 to
0.5V), a current begins to flow. Therefore, if cutting off the
output transistor at an I/O port puts the pin signal into the
high-impedance state, a current flow across the ports input
transistor, requiring to fix the level by pull-up or other
means.
Release the STOP mode
The exit from STOP mode is hardware reset or external in-
terrupt. Reset re-defines all the Control registers but does
not change the on-chip RAM. External interrupts allow
both on-chip RAM and Control registers to retain their val-
ues.
After releasing STOP mode, instruction execution is divid-
ed into two ways by I-flag(bit2 of PSW).
If I-flag = 1, the normal interrupt response takes place. If I-
flag = 0, the chip will resume execution starting with the
instruction following the STOP instruction. It will not vec-
tor to interrupt service routine. (refer to )
When exit from Stop mode by external interrupt, enough
oscillation stabilization time is required to normal opera-
tion. shows the timing diagram. When release the Stop
mode, the Basic interval timer is activated on wake-up. It
is increased from 00
H
until FF
H
. The count overflow is set
to start normal operation. Therefore, before STOP instruc-
tion, user must be set its relevant prescaler divide ratio to
have long enough time (more than 20msec). This guaran-
tees that oscillator has started and stabilized.
By reset, exit from Stop mode is shown in .
Minimizing Current Consumption in Stop Mode
The Stop mode is designed to reduce power consumption.
To minimize the current consumption during Stop mode,
the user should turn-off output drivers that are sourcing or
sinking current, if it is practical. Weak pull-ups on port
pins should be turned off, if possible. All inputs should be
either as V
SS
or at V
DD
(or as close to rail as possible).
An intermediate voltage on an input pin causes the input
buffer to draw a significant amount of current.
Figure 17-1 STOP Releasing Flow by Interrupts
Figure 17-2 Timing of STOP Mode Release by External Interrupt
IEXX
=0
=1
STOP
INSTRUCTION
STOP Mode
Interrupt Request
STOP Mode Release
I-FLAG
=1
Interrupt Service Routine
Next
INSTRUCTION
=0
Master Interrupt
Enable Bit PSW[2]
Corresponding Interrupt
Enable Bit (IENH, IENL)
~
STOP Mode
Normal Operation
Oscillator
(X
IN
pin)
~
~
N+1
N
N+2
00
01
FE
FF
00
01
N-1
N-2
~
~
~
~
~
Clear Basic Interval Timer
STOP Instruction Execution
Normal Operation
Stabilization Time
t
ST
> 20mS
Internal
Clock
External
Interrupt
BIT
Counter
~
相關PDF資料
PDF描述
HMS87C1302AD CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
HMS87C1304AD CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
HMS99C51 8-BIT SINGLE-CHIP MICROCONTROLLERS
HMS99C52 8-BIT SINGLE-CHIP MICROCONTROLLERS
HMS9XC7132 DATA SHEET REV.2.0(PRELIMINARY)
相關代理商/技術參數
參數描述
HMS87C1304AD 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
HMS87C1404B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
HMS87C1404BD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
HMS87C1404BSK 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
HMS87C1408B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
主站蜘蛛池模板: 铜梁县| 嵊州市| 徐州市| 塔河县| 京山县| 晋州市| 河津市| 贵德县| 宜宾县| 栾川县| 政和县| 华亭县| 汝南县| 漠河县| 襄樊市| 垣曲县| 苍梧县| 门头沟区| 威信县| 肇东市| 清远市| 九龙县| 娄烦县| 吉林市| 滨海县| 会泽县| 定日县| 滁州市| 麻城市| 锡林浩特市| 宕昌县| 石阡县| 遵义县| 宜良县| 南丹县| 紫云| 县级市| 山东省| 乐东| 汝州市| 萨迦县|