- 您現在的位置：買賣IC網 > PDF目錄385394 > HSDL-3020-021 (Avago Technologies Ltd.) IrDA㈢ Data Compliant Low Power 4.0 Mbit/s with Remote Control Infrared Transceiver PDF資料下載
參數資料
| 型號： | HSDL-3020-021 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s with Remote Control Infrared Transceiver |
| 中文描述： | 紅外線㈢數據兼容低功耗4.0 Mbit / s的紅外遙控器 |
| 文件頁數： | 14/24頁 |
| 文件大小： | 212K |
| 代理商： | HSDL-3020-021 |
14
Recommended Metal solder Stencil
Aperture
It is recommended that only a
0.152 mm (0.006 inch) or a
0.127 mm (0.005 inch) thick
stencil be used for solder paste
printing. This is to ensure
adequate printed solder paste
volume and no shorting. See
Table
1
, below the drawing, for combin-
ations of metal stencil aperture
and metal stencil thickness that
should be used. Aperture opening
for shield pad is 3.05 mm x 1.1
mm as per land pattern.
Figure 3. Solder stencil aperture.
Table 1.
Aperture Size (mm)
Stencil Thickness, t (mm)
Length, l
1.75
±
0.05
2.4
±
0.05
Width, w
0.55
±
0.05
0.55
±
0.05
0.127 mm
0.11 mm
APERTURES AS PER
LAND DIMENSIONS
l
w
t
Adjacent Land Keepout and Solder
Mask Areas
Adjacent land keepout is the
maximum space occupied by the
unit relative to the land pattern.
There should be no other SMD
components within this area.
The minimum solder resist strip
width required to avoid solder
bridging adjacent pads is
0.2 mm. It is recommended that
two fiducial crosses be placed at
mid length of the pads for unit
alignment.
Note:
Wet/Liquid Photo-imageable
solder resist/mask is recommended.
h
l
j
k
SOLDER MASK
DIMENSION
h
l
k
j
mm
0.2
3.0
3.85
11.9
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-3021 | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s with Remote Control Infrared Transceiver |
| HSDL-3021-021 | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s with Remote Control Infrared Transceiver |
| HSDL-3203 | Small Profile Package IrDA㈢ Data Compliant Low Power 115.2 kbit/s Infrared Transceiver |
| HSDL-3210 | IrDA㈢ Compliant Low Power 1.15 Mbit/s Infrared Transceiver |
| HSDL-3210-021 | IrDA㈢ Compliant Low Power 1.15 Mbit/s Infrared Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3021 | 制造商:Avago Technologies 功能描述:TRANSCEIVER IRDA 4MB/S |
| HSDL-3021-021 | 功能描述:紅外收發器 FIR + RC RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| HSDL-3200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IrDA 1.2 Data Compliant 115.2Kb/s 3V Infrared Transceiver |
| HSDL-3200#021 | 功能描述:紅外收發器 IR Transceiver 115.2Kb/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| HSDL-3200-921 | 制造商:Lite-On Semiconductor Corporation 功能描述:IRDA TX/RX 0.1152MBPS 2.7V TO 3.6V 8PIN - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。