- 您現在的位置：買賣IC網 > PDF目錄385394 > HSDL-3603-207 (Avago Technologies Ltd.) IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver PDF資料下載
參數資料
| 型號： | HSDL-3603-207 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| 中文描述： | 紅外線㈢數據符合4 Mbit / s的紅外收發器 |
| 文件頁數： | 3/29頁 |
| 文件大小： | 226K |
| 代理商： | HSDL-3603-207 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
3
I/O Pins Configuration Table
Pin
1
Symbol
LED A
Description
LED Anode
I/O Type
Input
Function
This pin can be connected directly to V
CC
(i.e., without series resistor)
at less than 3 V. Please refer to Table 1 for V
CC
versus Series Resistor, R1.
Leave this pin unconnected.
This pin is used to transmit serial data when SD/Mode pin is low. If this
pin is held high longer than ~100
μ
s, the LED would be turned off when
used in conjunction with the SD/Mode pin. TXD is low at initialization.
This pin is capable of driving a standard CMOS or TTL load. No external
pull-up or pull-down resistor is required. It is in tri-state mode when the
transceiver is in shutdown mode and during digital serial programming
operations. RXD is high at initialization.
The transceiver is in shutdown mode if this pin is high for more than
400
μ
s. On the falling edge of this signal, the state of the TXD pin sampled
and used to set receiver low bandwidth (TXD=low) or high bandwidth
(TXD=high) mode. See Figure 3 and Figure 4 for bandwidth selection
timings. SD is low at initialization.
Regulated, 2.7 to 5.25 Volts.
2
3
LED C
TXD
LED Cathode
Transmit Data
Output
Input,
Active High
4
RXD
Receive Data
Output,
Active Low
5
SD/Mode Shutdown/
Input,
Active High
Mode Select
6
V
CC
Supply
Voltage
No Connect
Ground
EMI Shield
Supply
Voltage
No Connect
Ground
EMI Shield
7
8
–
NC
GND
Shield
Connect to system ground.
Connect to system ground via a low inductance trace. For best
performance, do not connect directly to the transceiver pin GND.
Recommended Application Circuit Components
Component
R1
Recommended Value
0
±
5%, 0.5 Watt, for 2.7 V
1.8
±
5%, 0.5 Watt, for 3.0 V
4.7
±
5%, 0.5 Watt, for 3.3 V
6.8
±
5%, 0.5 Watt, for 3.5 V
0.47
μ
F
±
20%, X7R Ceramic
6.8
μ
F
±
20%, Tantalum
Notes
CX1
CX2
1
2
Notes:
1. CX1 must be placed within 0.7 cm of the HSDL-3603 to obtain optimum noise immunity.
2. In environments with noisy power supplies, supply rejection performance can be enhanced
by including CX2, as shown in Figure 1: ”HSDL-3603 Functional Block Diagram“ on Page 2.
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-3603-208 | IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| HSDL-4250 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4251 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4260 | High-Power T-1 (5mm) AlGaAs Infrared (875nm) Lamp |
| HSDL-4261 | High-Power T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3603-208 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| HSDL-3610 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IrDA 1.0 Data Compliant 115.2Kb/s 3-5V Infrared Transceiver(not recommended for new designs) |
| HSDL-3610#007 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#008 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#017 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。