欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HT48RA0A
廠商: Holtek Semiconductor Inc.
英文描述: 8-Bit Remote Type MCU
中文描述: 8位遙控型單片機
文件頁數: 9/31頁
文件大小: 328K
代理商: HT48RA0A
HT48RA0A
Rev. 1.70
9
July 16, 2003
Carrier
The HT48RA0A provides a carrier output which shares
the pin with PC0. It can be selected to be a carrier output
(REM) or level output pin (PC0) by code option. If the
carrier output option is selected, setting PC0= 0 to en-
able carrier output and setting PC0= 1 to disable it at
low level output.
The clock source of the carrier is implemented by in-
struction clock (system clock divided by 4) and pro-
cessed by a frequency divider to yield various carry
frequency.
Carry Frequency=
Clock Source
m 2
n
where m=2 or 3 and n=0~3, both are selected by code
option. If m=2, the duty cycle of the carrier output is 1/2
duty. If m=3, the duty cycle of the carrier output can be
1/2dutyor1/3dutyalsodeterminedbycodeoption(with
the exception of n=0).
Detailed selection of the carrier duty is shown below:
m 2
n
Duty Cycle
2, 4, 8, 16
1/2
3
1/3
6, 12, 24
1/2 or 1/3
The following table shows examples of carrier fre-
quency selection.
f
SYS
f
CARRIER
Duty
m 2
n
455kHz
37.92kHz
1/3 only
3
56.9kHz
1/2 only
2
Input/Output Ports
There are an 8-bit bidirectional input/output port, a 6-bit
input with 2-bit I/O port and one-bit output port in the
HT48RA0A,labeledPA,PBandPCwhicharemappedto
[12H], [14H], [16H] of the RAM, respectively. Each bit of
PA can be selected as NMOS output or Schmitt trigger
with pull-high resistor by software instruction. PB0~PB1
have the same structure with PA, while PB2~PB7 can
only be used for input operation (Schmitt trigger with
pull-high resistors). PC is only one-bit output port shares
the pin with carrier output. If the level option is selected,
the PC is CMOS output.
Both PA and PB for the input operation, these ports are
non-latched, that is, the inputs should be ready at the T2
rising edge of the instruction MOV A, [m] (m=12H or
14H). For PA, PB0~PB1 and PC output operation, all
data are latched and remain unchanged until the output
latch is rewritten.
When the PA and PB0~PB1 is used for input operation,
it should be noted that before reading data from pads, a
1 should be written to the related bits to disable the
NMOS device. That is, the instruction SET[m].i (i=0~7
for PA, i=0~1 for PB) is executed first to disable related
NMOSdevice,andthen MOVA,[m] togetstabledata.
After chip reset, PA and PB remain at a high level input
line while PC remain at high level output, if the level op-
tion is selected.
Each bit of PA, PB0~PB1 and PC output latches can be
set or cleared by the
(m=12H, 14H or 16H) instructions respectively.
SET [m].i
and
CLR [m].i
Some instructions first input data and then follow the
output operations. For example, SET [m].i , CLR [m] ,
CPL [m] , CPLA [m] read the entire port states into
theCPU,executethedefinedoperations(bit-operation),
and then write the results back to the latches or to the
accumulator.
Each line of PB has a wake-up capability to the device
by code option. The highest seven bits of PC are not
physically implemented, on reading them a 0 is re-
turned and writing results in a no-operation.
!
"
#
# $ %
#
%
&
'
(
# # "
)
" * +
'
(
#
#
,
#
#
,
Carrier/Level output
相關PDF資料
PDF描述
HT48RA3 8-Bit Remote Type OTP MCU
HT48RB8 8-Bit USB Type OTP MCU
HT49C10 8-BIT MICROCONTROLLER
HT49C30L HDSP-A101 RED DISPLAY, LED,
HT49R30 DISPLAY 7 SEGMENT
相關代理商/技術參數
參數描述
HT48RA0A(20SOP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|SOP|20PIN|PLASTIC
HT48RA0A(24SOP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|SOP|24PIN|PLASTIC
HT48RA0A-20SOP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
HT48RA0A-24SOP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
HT48RA1 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU
主站蜘蛛池模板: 交口县| 闽侯县| 富阳市| 聂拉木县| 漠河县| 浦县| 乐平市| 南京市| 伊宁县| 毕节市| 锦州市| 博白县| 油尖旺区| 长沙市| 改则县| 宁晋县| 甘肃省| 张家口市| 岳池县| 三原县| 崇礼县| 马鞍山市| 古蔺县| 麟游县| 康乐县| 吉木萨尔县| 马龙县| 南郑县| 小金县| 上高县| 南陵县| 扶余县| 南木林县| 崇左市| 磐安县| 渭南市| 鹤峰县| 江都市| 井研县| 阿瓦提县| 道孚县|