- 您現在的位置：買賣IC網 > PDF目錄385400 > HT48RA3 (Holtek Semiconductor Inc.) 8-Bit Remote Type OTP MCU PDF資料下載
參數資料
| 型號： | HT48RA3 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit Remote Type OTP MCU |
| 中文描述： | 8位單片機的遠程型檢察官辦公室 |
| 文件頁數： | 13/36頁 |
| 文件大小： | 245K |
| 代理商： | HT48RA3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
HT48RA3
Rev. 1.20
13
May 12, 2003
There are 3 registers related to Timer/Event Counter 1;
TMR1H(0FH), TMR1L(10H), TMR1C(11H). Writing
TMR1L will only put the written data to an internal
lower-order byte buffer (8 bits) and writing TMR1H will
transfer the specified data and the contents of the
lower-order byte buffer to TMR1H and TMR1L preload
registers, respectively. The Timer/Event Counter 1
preload register is changed by each writing TMR1H op-
erations. Reading TMR1H will latch the contents of
TMR1H and TMR1L counters to the destination and the
lower-order byte buffer, respectively. Reading the
TMR1L will read the contents of the lower-order byte
buffer. The TMR1C is the Timer/Event Counter 1 control
register,whichdefinestheoperatingmode,countingen-
able or disable and active edge.
The TM0, TM1 bits define the operating mode. The
event count mode is used to count external events,
which means the clock source comes from an external
(TMR1) pin. The timer mode functions as a normal timer
with the clock source coming from the instruction clock.
The pulse width measurement mode can be used to
count the high or low level duration of the external signal
(TMR1).Thecountingisbasedontheinstructionclock.
In the event count or timer mode, once the Timer/Event
Counter 1 starts counting, it will count from the current
contents in the Timer/Event Counter 1 to FFFFH. Once
overflow occurs, the counter is reloaded from the
Timer/Event Counter 1 preload register and generates
the corresponding interrupt request flag (T1F; bit 6 of
INTC) at the same time.
In pulse width measurement mode with the TON and TE
bits are equal to one, once the TMR1 has received a
transitionfromlowtohigh(orhightolowiftheTEbitis0)
it will start counting until the TMR1 returns to the original
level and reset the TON. The measured result will re-
main in the Timer/Event Counter 1 even if the activated
transition occurs again. In other words, only one cycle
measurement can be done. Until setting the TON, the
cycle measurement will function again as long as it re-
ceives further transition pulse. Note that, in this operat-
ing mode, the Timer/Event Counter 1 starts counting not
according to the logic level but according to the transi-
tion edges. In the case of counter overflows, the counter
1 is reloaded from the Timer/Event Counter 1 preload
register and issues the interrupt request just like the
other two modes.
To enable the counting operation, the timer ON bit(TON;
bit 4 of TMR1C) should be set to 1. In the pulse width
measurement mode, the TON will be cleared automati-
callyafterthemeasurementcycleiscomplete.Butinthe
other two modes the TON can only be reset by instruc-
tions. The overflow of the Timer/Event Counter 1 is one
of the wake-up sources. No matter what the operation
mode is, writing a 0 to ET1I can disabled the corre-
sponding interrupt service.
In the case of Timer/Event Counter 1 OFF condition,
writing data to the Timer/Event Counter 1 preload regis-
ter will also load the data to Timer/Event Counter 1. But
if the Timer/Event Counter 1 is turned on, data written to
the Timer/Event Counter 1 will only be kept in the
, +
# ' ! )
!
'
,
!
#
>
! ,
!
,
' ,
# !
2 9 < # !
#
>
! ,
!
6
7
! , -
'
>
@
! , !
" !
2 9 !
,
2 9 ,
.
6
.
0 3 7
Timer/Event Counter 0
, +
# ' ! )
!
'
,
!
3 9 < # !
#
>
! ,
!
' ,
# !
! , -
'
>
@
! , !
" !
3 9 < # !
#
>
! ,
!
6
=
( 7
(
@ , - & !
-
1
Timer/Event Counter 1
相關PDF資料 |
PDF描述 |
|---|---|
| HT48RB8 | 8-Bit USB Type OTP MCU |
| HT49C10 | 8-BIT MICROCONTROLLER |
| HT49C30L | HDSP-A101 RED DISPLAY, LED, |
| HT49R30 | DISPLAY 7 SEGMENT |
| HT49R30A-1 | DISPL 7 SEG YELLOW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48RA3_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48RA3_09 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:HT48RA3/HT48CA3 |
| HT48RA5 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48RA5_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48RA5_09 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。