- 您現在的位置：買賣IC網 > PDF目錄385400 > HT49C50 (Holtek Semiconductor Inc.) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | HT49C50 |
| 廠商： | Holtek Semiconductor Inc. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 19/52頁 |
| 文件大小： | 318K |
| 代理商： | HT49C50 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
HT49C50
19
August 18, 1999
All I/O ports maintain their original status.
The PD flag is set but the TO flag is cleared.
LCD driver is still running (if the WDT OSC
or RTC OSC is selected).
The system quits the HALT mode by an external
reset, an interrupt, an external falling edge sig-
nalonportA,oraWDToverflow.Anexternalre-
set causes device initialization, and the WDT
overflowperformsa warmreset .Afterexamin-
ing the TO and PD flags, the reason for chip re-
set can be determined. The PD flag is cleared by
system power-up or by executing the
WDT instruction, and is set by executing the
HALT instruction. On the other hand, the TO
flag is set if WDT time-out occurs, and causes a
wake-up that only resets the PC (Program
Counter) and SP, and leaves the others at their
original state.
CLR
The port Awake-up and interrupt methods can
be considered as a continuation of normal exe-
cution. Each bit in port A can be independently
selected to wake up the device by mask option.
Awakening from an I/O port stimulus, the pro-
gram resumes execution of the next instruc-
tion. On the other hand, awakening from an
interrupt, two sequences may occur. If the re-
lated interrupt is disabled or the interrupt is
enabled but the stack is full, the program re-
sumes execution at the next instruction. But if
the interrupt is enabled, and the stack is not
full,theregularinterruptresponsetakesplace.
When an interrupt request flag is set before en-
tering the halt status, the system cannot be
awaken using that interrupt.
If wake-up events occur, it takes 1024 t
SYS
(sys-
tem clock period) to resume normal operation.
In other words, a dummy period is inserted af-
ter the wake-up. If the wake-up results from an
interrupt acknowledgment, the actual inter-
rupt subroutine execution is delayed by more
than one cycle. However, if the Wake-up results
in the next instruction execution, the execution
will be performed immediately after the
dummy period is finished.
To minimize power consumption, all the I/O
pins should be carefully managed before enter-
ing the HALT status.
Reset
Therearethreewaysinwhichresetmayoccur.
RES is reset during normal operation
RES is reset during HALT
WDT time-out is reset during normal
operation
The WDT time-out during HALT differs from
other chip reset conditions, for it can perform a
warm reset that resets only the PC and SP
and leaves the other circuits at their original
state. Some registers remain unaffected during
any other reset conditions. Most registers are
reset to the initial condition once the reset
conditions are met. Examining the PD and TO
flags, the program can distinguish between dif-
ferent chip resets .
TO
PD
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal
operation
0
1
RES Wake-up HALT
1
u
WDT time-out during normal
operation
1
1
WDT Wake-up HALT
Note:
u means unchanged
*
, & &
Reset circuit
相關PDF資料 |
PDF描述 |
|---|---|
| HT49R50A | 8-Bit High Performance High speed Microcontroller(8位、高性能、高速微控制器) |
| HT49R50 | 8-BIT MICROCONTROLLER |
| HT5D048 | 0.8m CMOS High Speed Gate Array(0.8m CMOS高速門陣列) |
| HT5D028 | 0.8m CMOS High Speed Gate Array(0.8m CMOS高速門陣列) |
| HT5D064 | 0.8m CMOS High Speed Gate Array(0.8m CMOS高速門陣列) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT49C50-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit LCD Type Mask MCU |
| HT49C50-1_12 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type 8-Bit MCU |
| HT49C50-100QFP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| HT49C50-80QFP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| HT49C50L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit LCD Type Low Voltage Mask MCU |
發布緊急采購，3分鐘左右您將得到回復。