- 您現在的位置：買賣IC網 > PDF目錄385403 > HT82A821R_07 (Holtek Semiconductor Inc.) USB Audio MCU PDF資料下載
參數資料
| 型號： | HT82A821R_07 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Audio MCU |
| 中文描述： | USB音頻控制器 |
| 文件頁數： | 13/39頁 |
| 文件大小： | 275K |
| 代理商： | HT82A821R_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
HT82A821R
Rev. 1.10
13
June 29, 2007
Bit No.
Label
Function
0~2, 5
Unused bit, read as 0
3
TE
Defines the TMR active edge of the timer/event counter
In Event counter mode (TM1, TM0)=(0, 1):
1=count on falling edge;
0=count on rising edge
In Pulse width measurement mode (TM1, TM0)=(1, 1):
1=start counting on the rising edge, stop on the falling edge;
0=start counting on the falling edge, stop on the rising edge
4
TON
Enable/disable the timer counting (0=disable; 1=enable)
6
7
TM0
TM1
Defines the operating mode
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
TMRC (11H) Register
Timer/Event Counter
Two timer/event counters (TMR0, TMR1) are imple-
mented in the microcontroller. The timer/event counter
0/1 contains a 16-bit programmable count-up counter
and the clock may come from an external source or an
internal clock source. An internal clock source comes
from f
SYS
/4. The external clock input allows the user to
count external events, measure time intervals or pulse
widths, or to generate an accurate time base. There are
six registers related to the Timer/Event Counter 0;
TMR0H (0CH), TMR0L (0DH), TMR0C (0EH) and the
Timer/Event Counter 1; TMR1H (0FH), TMR1L (10H),
TMR1C (11H). For 16-bit timer to write data to TMR0/1L
will only put the written data to an internal lower-order
byte buffer (8-bit) and writing TMR0/1H will transfer the
specified data and the contents of the lower-order byte
buffer to TMR0/1H and TMR0/1L registers. The
Timer/Event Counter 0/1 preload register is changed by
each writing TMR0/1H operations. Reading TMR0/1H
will latch the contents of TMR0/1H and TMR0/1L coun-
ters to the destination and the lower-order byte buffer,
respectively. Reading the TMR0/1L will read the con-
tents of the lower-order byte buffer. The TMR0/1C is the
Timer/Event Counter 0/1 control register, which defines
the operating mode, counting enable or disable and an
active edge.
The TM0 and TM1 bits define the operation mode. The
event count mode is used to count external events,
which means that the clock source is from an external
(TMR0, TMR1) pin. The timer mode functions as a nor-
mal timer with the clock source coming from the internal
clock source. Finally, the pulse width measurement
mode can be used to count the high level or low level du-
ration of the external signal (TMR0, TMR1), and the
counting is based on the internal clock source.
In the event count or timer mode, the timer/event coun-
ter starts counting at the current contents in the
timer/event counter and ends at FFFFH. Once an over-
flow occurs, the counter is reloaded from the timer/event
counter preload register, and generates an interrupt re-
quest flag (T0F; bit 5 of INTC0, T1F; bit 6 of INTC0). In
the pulse width measurement mode with the values of
the TON and TE bits equal to 1, after the TMR0 (TMR1)
hasreceivedatransientfromlowtohigh(orhightolowif
the TE bit is 0 ), it will start counting until the TMR0
(TMR1) returns to the original level and resets the TON.
The measured result remains in the timer/event counter
even if the activated transient occurs again. In other
words, only 1-cycle measurement can be made until the
TON is set. The cycle measurement will re-function as
long as it receives further transient pulse. In this opera-
tion mode, the timer/event counter begins counting not
according to the logic level but to the transient edges. In
the case of counter overflows, the counter is reloaded
from the timer/event counter register and issues an in-
terrupt request, as in the other two modes, i.e., event
and timer modes.
)
) (
'
)
&
%
"
%
&
6 % ,
( ' A
%
&
%
% ,
&
A
# & 8
%
#
/
( 0
6 % ,
( ' A
%
;
) ( <
#
Timer/Event Counter 0/1
相關PDF資料 |
PDF描述 |
|---|---|
| HT82A822R | USB Audio MCU |
| HT82A822R_07 | USB Audio MCU |
| HT82A832R | Basic USB Phone OTP MCU |
| HT82A850R | Audio MCU |
| HT82A851R | USB Audio MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82A822R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Audio MCU |
| HT82A822R_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Audio MCU |
| HT82A824R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Audio MCU |
| HT82A832R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Audio MCU |
| HT82A832R_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Audio MCU |
發布緊急采購，3分鐘左右您將得到回復。