- 您現在的位置：買賣IC網 > PDF目錄385403 > HT82J30A (Holtek Semiconductor Inc.) 16 Channel A/D MCU with SPI Interface PDF資料下載
參數資料
| 型號： | HT82J30A |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 16 Channel A/D MCU with SPI Interface |
| 中文描述： | 16通道A / D轉換，SPI接口單片機 |
| 文件頁數： | 21/47頁 |
| 文件大小： | 312K |
| 代理商： | HT82J30A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
HT82J30R/HT82J30A
Rev. 1.00
21
December 20, 2006
mentioned in the description.
Two corresponding registers, SBCR and SBDR are
unique to the serial interface and provide control, status,
and data storage.
SBCR_A, SBCR_B: Serial bus control register
Bit7 (CKS) clock source selection: f
SIO
=f
SYS
/4,
select as 0
Bit6(M1),Bit5(M0)master/slavemodeandbaudrate
selection
M1, M0: 00
MASTER MODE, BAUD RATE= f
SIO
MASTER MODE, BAUD RATE= f
SIO
/4
MASTER MODE, BAUD RATE= f
SIO
/16
SLAVE MODE
01
10
11
Bit4 (SBEN)
serial bus enable/disable (1/0)
Enable: (SCS dependent on CSEN bit)
Disable
(SCKB= 0 ) and waiting for writing data to SBDR
(TXRX buffer)
enable: SCK, SDI, SDO, SCS= 0
Master mode: write data to SBDR (TXRX buffer)
start transmission/reception automatically
Master mode: when the data has been transferred,
set TRF
Slave mode: when an SCK (and SCS dependent on
CSEN) is received, data in the TXRX buffer is
shifted-out and data on SDI is shifted-in.
Disable: SCK (SCK), SDI, SDO, SCS floating
Bit3(MLS)
MSBorLSB(1/0)shiftfirstcontrolbit
Bit2 (CSEN)
able (SCS), when CSEN=0, SCSB is floating.
serial bus selection signal enable/dis-
Bit1 (WCOL)
the SBDR register (TXRX buffer) when data is
transferred, writing will be ignored if data is written
to SBDR (TXRX buffer) when data is transferred.
this bit is set to 1 if data is written to
Bit0 (TRF)
used to generate an interrupt.
data transferred or data received
Note: data reception is still in operation when the
MCU enters the Power-down mode.
SBDR_A, SBDR_B: Serial bus data register
Data written to SBDR
only
write data to the TXRX buffer
Data read from SBDR
Operating Mode description:
Master transmitter: clock transmission and data I/O
started by writing to SBDR
MasterclocktransmissioninitiatedbywritingtoSBDR
Slave transmitter: data I/O started by clock reception
Slave receiver: data I/O started by clock reception
read from SBDR only
0
/
,
,
/
0
6
6 1
0
/
,
,
/
0
6
6 1
$ 6
$ 6 1
6
6 1
1
6
1
6 1
.
(
1
6
1
6 1
.
(
@ D
D
&
# )
' E
$
1
(
4
(
.
0
/
,
0
/
,
1
@
( 1
(
+
1
@
( 1
+
6
$
$
6
$
SPI Serial Interface
There are two SPI interfaces, with each interface containing four basic signals and pins. These are SDI (serial data in-
put), SDO (serial data output), SCK (serial clock) and SCS (slave select pin). Note that each of these pin names will be
suffixedwitheitheranAorBtodenotewhichSCIinterfaceisbeingused,howevertominimiserepetition,thiswillnotbe
相關PDF資料 |
PDF描述 |
|---|---|
| HT82J30R | 16 Channel A/D MCU with SPI Interface |
| HT82J927A | USB Gamepad |
| HT82J97E | USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E-20SOP-A | USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E-28SOP-A | USB Joystick Encoder 8-Bit OTP MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82J30R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16 Channel A/D MCU with SPI Interface |
| HT82J927A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Gamepad |
| HT82J97A_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit MCU |
| HT82J97E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。