- 您現在的位置：買賣IC網 > PDF目錄385407 > HT95A300 (Holtek Semiconductor Inc.) I/O Type Phone 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT95A300 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | I/O Type Phone 8-Bit MCU |
| 中文描述： | I / O型電話8位微控制器 |
| 文件頁數： | 19/48頁 |
| 文件大小： | 360K |
| 代理商： | HT95A300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
HT95AXXX
Rev. 1.20
19
May 26, 2004
Each I/O line has its own control register (PAC, PBC,
PDC, PEC, PFC, PGC) to control the input/output con-
figuration. With this control register, CMOS output or
Schmitt trigger input can be reconfigured dynamically
under software control. To make one I/O line to function
as an input line, the corresponding latch of the control
register must be written with a 1 . The pull-high resis-
tance shows itself automatically if the pull-high option is
selected. The input source also depends on the control
register. If the control register bit is 1 , the input will
read the pad state. If the control register bit is 0 , the
contents of the latches will move to the internal bus. The
latter is possible in the read-modify-write instruction.
For output function, CMOS is the only configuration.
Each bit of these input/output latches can be set or
cleared by SET [m].i and CLR [m].i (m=12H, 14H,
18H, 1AH, 34H or 36H) instructions.
Some instructions first input data and then follow the
output operations. For example,
SET [m].i ,
CLR
[m].i , CPL [m] , CPLA [m] read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of port A has the capability of waking-up the
device. They are selected by mask option per bit.
There is a pull-high option available for all I/O lines.
Once the pull-high option of an I/O line is selected, the
I/O lines have pull-high resistor. Otherwise, the pull-high
resistor is absent. It should be noted that a non-pull-high
I/O line operating in input mode may cause a floating
state.
I/O port pull-high, wake-up function are selected by
mask option
I/O Port
Output
Input
Supported for HT95AXXX
Pull-high Resistor
Wake-up Function
400/P
300/P
200/P
100/P
PA7~PA0
CMOS
Selected per bit
Selected per bit
PB7~PB0
CMOS
Selected per bit
PD3~PD0
CMOS
Selected per nibble
PD7~PD4
CMOS
Selected per nibble
PE3~PE0
CMOS
Selected per nibble
PE7~PE4
CMOS
Selected per nibble
PF7~PF0
CMOS
Selected per nibble
PG3~PG0
CMOS
Selected per nibble
Note:
means unavailable
!
"
!
#
$
%
& '
% (
%
& '
% (
&
$
(
(
$
&
$
!
#
$
& )
!
!
" &
$
!
#
$
$
!
#
$
(
Input/Output Ports
相關PDF資料 |
PDF描述 |
|---|---|
| HT95AXXX | I/O Type Phone 8-Bit MCU |
| HT95C20P | 8-Bit CID Type Phone Controller MCU |
| HT95C300 | 8-Bit CID Type Phone Controller MCU |
| HT95C30P | 8-Bit CID Type Phone Controller MCU |
| HT95C200 | 8-Bit CID Type Phone Controller MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT95A300/30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type Phone 8-Bit MCU |
| HT95A30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95A400 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type Phone 8-Bit MCU |
| HT95A400/40P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type Phone 8-Bit MCU |
| HT95A40P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。