- 您現在的位置：買賣IC網 > PDF目錄385407 > HT95L300 (Holtek Semiconductor Inc.) 8-Bit LCD Type Phone Controller MCU PDF資料下載
參數資料
| 型號： | HT95L300 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit LCD Type Phone Controller MCU |
| 中文描述： | 8位LCD型電話MCU控制器 |
| 文件頁數： | 23/42頁 |
| 文件大小： | 768K |
| 代理商： | HT95L300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
HT95L100/10P
Rev. 0.10
23
October 1, 2002
Preliminary
LCD driver
The LCD driver can directly drive an LCD panel with 1/8
duty and 1/4 bias. The frame of this LCD driver is fixed
for 64Hz.
LCD driver uses the voltage of the VLCD pin as the
power source. To adjust the view angle, the programmer
can select the real LCD power by the flags VCON0 and
VCON1.TheflagLCDONisusedtoturnOn/OfftheLCD
display. Note that the VLCD voltage must equal or be
less than VDD.
Segment/Common to I/O selection
For the flexible purpose, some of the LCD SEGMENT
pins are shared with the input/output port.
HT95L100/10P provides 4 pins to be selected to SEG-
MENT output pins or I/O pins.
LCD display memory
The phone controller provides an area on embedded
data memory for LCD display. The LCD display memory
are located at bank 1BH and can be read and written to,
only by indirect addressing mode using MP1. When
data is written into the display data area it is automati-
cally read by the LCD driver which then generates the
corresponding LCD driving signals, to turn the display
On or Off, a 1 or 0 is written to the corresponding bit
of the display memory, respectively. All of the LCD dis-
play memories are with random values after the power
on reset and unchanged after other reset conditions.
Register
Label
Bits
R/W
Function
LCDC
(2DH)
LBEN
2
RW
Low battery detection switch
0: disable the low battery detection
1: enable the low battery detection
3,1,0
RO
Unused bit, read as 0
LBFG
4
RO
Low battery detection flag
1: LBIN pin voltage is less than 1.25V
0: LBIN pin voltage is not less than 1.25V
VCON0
VCON1
5
6
RW
LCD contrast adjusting
Bit6,5=00: LCD voltage supply is 0.66 VLCD
Bit6,5=10: LCD voltage supply is 0.82 VLCD
Bit6,5=01: LCD voltage supply is 0.93 VLCD
Bit6,5=11: LCD voltage supply is 1.00 VLCD
LCDON
7
RW
1: Turn on the LCD display
0: Turn off the LCD display
LCDIO
(28H)
4~0
7~6
RO
Unused bit, read as 0
SPE0
5
RW
0: SEG16~SEG19 pins are LCD segment output
1: SEG16~SEG19 pins are PE0~PE3 pins
COM7 to COM0 for HT95L100/10P
Address
Register
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
8CH
SEG0
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
8DH
SEG1
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
9EH
SEG18
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
9FH
SEG19
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
相關PDF資料 |
PDF描述 |
|---|---|
| HT95A20P | 8-Bit LCD Type Phone Controller MCU |
| HT95L300-100QEP-A | LCD Type Phone 8-Bit MCU |
| HT95A400 | Time-Delay Relay; Mounting Type:Plug In; Relay Mounting:Plug-In |
| HT95A100 | I/O Type Phone 8-Bit MCU |
| HT95A200 | I/O Type Phone 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT95L300-100QEP-A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU |
| HT95L30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95L30P-100QEP-A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU |
| HT95L400 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95L400-128QFP-A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。