- 您現在的位置：買賣IC網 > PDF目錄385411 > HV9605P (SUPERTEX INC) High Voltage Current Mode PWM Controller for ISDN Equipment PDF資料下載
參數資料
| 型號： | HV9605P |
| 廠商： | SUPERTEX INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High Voltage Current Mode PWM Controller for ISDN Equipment |
| 中文描述： | SWITCHING CONTROLLER, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 4/5頁 |
| 文件大小： | 33K |
| 代理商： | HV9605P |
4
HV9605
11/30/98
1
7
6
5
4
3
2
14
13
12
11
10
9
8
14 Pin SOIC/DIP Package
COMP
FB
NI
STATUS
RT
SGND
OUT
+V
IN
STOP
START
REF
V
DD
PGND
CS
Pin Description
SGND
- Common connection for all low level signal and digital
circuits. While SGND and PGND must be electrically connected
together, having separate common pins enhances the ability of
the designer to prevent coupling of noise into critical circuits.
PGND
- This pin provides common return for the high transient
current of the output driver circuits. While PGND and SGND must
be electrically connected, having a separate connection prevents
common noise created by the high transient currents of the output
driver from being injected into critical circuits.
+V
IN
accept DC input voltages in the range of 15V to 250V. With
START and STOP set to more than 20V, the leakage current on
this pin is less than 6.0
μ
A at +V
IN
= 20V.
START
- The resistive divider from +V
IN
sets the start voltage.
STOP
- The resistive divider from +V
IN
sets the stop voltage.
V
DD
- This is the supply pin for the PWM circuits. When the
input voltage to the +V
IN
pin exceeds the start voltage the input
regulator seeks to regulate the voltage on the capacitor con-
nected to this pin to a nominal 4.5V.
- This is the start-up linear pre-regulator input which can
OUT
to drive the gate of a power MOSFET. In order to protect the
power MOSFET in high electrical noise environment, this output
appears as low impedance to PGND when V
DD
is at zero volts.
CS
- This is the current sense input to the PWM compara-
tors. Under normal operation the over current limit is triggered
when the voltage on this pin is at 0.70V and the loop control
operating peak current may be set to any level below this, typically
in the range of 0.2 to 0.5V.
- This high current push-pull CMOS output is intended
COMP
- The low impedance output of the error amplifier.
FB
- The high impedance inverting input of the error amplifier.
NI
- The high impedance non-inverting input of the error
amplifier.
REF
impedance buffered reference which is current limited to 0.5mAmps
and should be bypassed, REF to SGND, with a 0.1
μ
F ceramic
capacitor.
- This pin provides a 2% accuracy 1.20V low output
RT
frequency of the internal oscillator by setting the charging current
for the internal timing capacitor. The oscillator frequency is twice
the PWM output frequency.
- The resistor connected from this pin to SGND sets the
STATUS
- This output is held low until the +V
IN
voltage reaches
the programmed START voltage. It remains low until the boot-
strap supply to V
DD
forces the voltage above the internal regulator
set point. It is further held low while the control amplifier output on
the COMP pin is forced to its high limit by a low output from the
converter. Once all these conditions are satisfied, this output will
rise to V
DD
with a time constant set by the external capacitor
indicating that normal operation has been reached. This output
may be used to control the reset of a microprocessor.
Pin Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| HV9605X | High Voltage Current Mode PWM Controller for ISDN Equipment |
| HVC | High Voltage Chip Resistors |
| HVC2512-4M7DT3 | High Voltage Chip Resistors |
| HVC2512-4M7FT3 | High Voltage Chip Resistors |
| HVC2512-4M7GT3 | High Voltage Chip Resistors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV9605X | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:High Voltage Current Mode PWM Controller for ISDN Equipment |
| HV9606 | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:HV9606 Current-Mode PWM Controller with Supervisor |
| HV9606DB1 | 功能描述:電源管理IC開發工具 HV9606 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV9606DB2 | 功能描述:電源管理IC開發工具 HV9606 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV9606SP | 功能描述:開關變換器、穩壓器與控制器 Crnt Mode PWM RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。