欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HY29F400TR45
廠商: Hynix Semiconductor Inc.
英文描述: 128 x 64 pixel format, White LED backlight
中文描述: 4兆位(512Kx8/256Kx16)5伏只閃存
文件頁數: 18/40頁
文件大小: 509K
代理商: HY29F400TR45
18
Rev. 5.2/May 01
HY29F400
HARDWARE DATA PROTECTION
The HY29F400 provides several methods of pro-
tection to prevent accidental erasure or program-
ming which might otherwise be caused by spuri-
ous system level signals during V
CC
power-up and
power-down transitions, or from system noise.
These methods are described in the sections that
follow.
Command Sequences
Commands that may alter array data require a
sequence of cycles as described in Table 5. This
provides data protection against inadvertent writes.
Low V
CC
Write Inhibit
To protect data during V
CC
power-up and power-
down, the device does not accept write cycles
when V
CC
is less than V
LKO
(typically 3.7 volts). The
command register and all internal program/erase
circuits are disabled, and the device resets to the
Read mode. Writes are ignored until V
CC
is greater
than V
LKO
. The system must provide the proper
signals to the control pins to prevent unintentional
writes when V
CC
is greater than V
LKO
.
sector erase timer does not apply to the Chip Erase
command.
After the initial Sector Erase command sequence
is issued, the system should read the status on
DQ[7] (Data# Polling) or DQ[6] (Toggle Bit I) to
ensure that the device has accepted the command
sequence, and then read DQ[3]. If DQ[3] is a
1
,
the internally controlled erase cycle has begun and
all further sector erase data cycles or commands
Read DQ[7:0]
at Valid Address (Note 1)
DQ[6] Toggled
NO
(Note 3)
YES
PROGRAM/ERASE
COMPLETE
DQ[5] = 1
NO
YES
Read DQ[7:0]
at Valid Address (Note 1)
DQ[6] Toggled
(Note 2)
NO
YES
PROGRAM/ERASE
EXCEEDED TIME ERROR
Notes
:
1. During programming, the program address.
During sector erase, an address within any sector scheduled for erasure.
2. Recheck DQ[6] since toggling may stop at the same time as DQ[5] changes from 0 to 1.
3. Use this path if testing for Program/Erase status.
4. Use this path to test whether sector is in Erase Suspend mode.
Read DQ[7:0]
at Valid Address (Note 1)
START
Read DQ[7:0]
DQ[2] Toggled
NO
SECTOR BEING READ
IS IN ERASE SUSPEND
Read DQ[7:0]
YES
NO
(Note 4)
SECTOR BEING READ
IS NOT IN ERASE SUSPEND
Figure 8. Toggle Bit I and II Test Algorithm
(other than Erase Suspend) are ignored until the
erase operation is complete. If DQ[3] is a
0
, the
device will accept a sector erase data cycle to mark
an additional sector for erasure. To ensure that
the data cycles have been accepted, the system
software should check the status of DQ[3] prior to
and following each subsequent sector erase data
cycle. If DQ[3] is high on the second status check,
the last data cycle might not have been accepted.
相關PDF資料
PDF描述
HY29F400TR55 128 x 64 pixel format, White or blue LED backlight
HY29F400TR70 128 x 64 pixel format, White or blue LED backlight
HY29F400TR90 150 x 32 pixel format, LED Backlight available
HY29F400BG70 MS3470L14-5A
HY29F400BG90 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
相關代理商/技術參數
參數描述
HY29F400TR-45 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
HY29F400TR55 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400TR-55 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
HY29F400TR70 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400TR-70 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
主站蜘蛛池模板: 稷山县| 武威市| 蒲城县| 寿光市| 河东区| 张掖市| 介休市| 延庆县| 德钦县| 民权县| 繁昌县| 正宁县| 许昌市| 昂仁县| 莱阳市| 兴仁县| 南康市| 玉林市| 玛沁县| 崇明县| 柘城县| 元谋县| 木兰县| 东山县| 凯里市| 通江县| 花莲县| 迁西县| 同江市| 将乐县| 泰来县| 安国市| 竹北市| 杂多县| 新蔡县| 邯郸市| 星子县| 潢川县| 红河县| 深州市| 合山市|