- 您現在的位置：買賣IC網 > PDF目錄383139 > ISL6118 (Intersil Corporation) Octal Transparent D-Type Latches With 3-State Outputs 20-SO -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6118 |
| 廠商： | Intersil Corporation |
| 英文描述： | Octal Transparent D-Type Latches With 3-State Outputs 20-SO -40 to 85 |
| 中文描述： | 雙電源控制器 |
| 文件頁數： | 1/10頁 |
| 文件大小： | 454K |
| 代理商： | ISL6118 |
1
FN9008.2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL6118
Dual Power Supply Controller
The ISL6118 is a dual channel, fully independent overcurrent
(OC) fault protection IC for the +2.5V to +5.5V environment.
This device features internal current monitoring, accurate
current limiting, integrated power switches and current
limited delay to latch-off for system protection.
The ISL6118 current sense and limiting circuitry sets the
current limit to a nominal 0.6A, which is well suited for the
3.3VAUX ACPI application. The ISL6118 is the ideal
companion chip to the HIP1011D and HIP1011E dual PCI
hot plug controllers. Together these and the ISL6118 fully
control the four legacy PCI voltages (±12V, +3.3V, +5V) and
the 3.3V AUX, respectively, for power control of two PCI
slots compliant to PCI Bus Power Management Interface
Spec Rev 1.1. Designed to be co-located with the HIP1011D
on the motherboard, the ISL6118 provides OC fault
notification, accurate current limiting and a consistent timed
latch-off thus isolating and protecting the voltage bus in the
presence of an OC event or short circuit during all PCI Bus
Power States as defined by the PCI specification. The 12ms
time to latch-off is independent of the adjoining switch’s
electrical or thermal condition and the OC response time is
inversely related to the OC magnitude.
Each ISL6118 incorporates in a single 8-lead SOIC
package two 80m
N-channel MOSFET power switches
for power control. Each switch is driven by a constant
current source giving a controlled ramp up of the output
voltage. This provides a soft start turn-on eliminating bus
voltage drooping caused by inrush current while charging
heavy load capacitances. Independent enabling inputs and
fault reporting outputs for each channel are compatible with
3V and 5V logic to allow external control and monitoring.
The ISL6118 undervoltage (UV) feature prevents turn-on of
the outputs unless the correct ENABLE state and
VIN > 2.5V are present. During initial turn-on the ISL6118
prevents fault reporting by blanking the fault signal. Rising
and falling outputs are current-limited voltage ramps so that
both the inrush current and voltage slew rate are limited,
independent of load. This reduces supply droop due to
surge and eliminates the need for external EMI filters.
During operation, once an OC condition is detected the
appropriate output is current limited for 12ms to allow
transient conditions to pass. If still in current limit after the
current limit period has elapsed, the output is latched off
and the fault is reported by pulling the corresponding
FAULT low. The FAULT signal is latched low until reset by
the ENABLE signal being de-asserted at which time the
FAULT signal will clear.
Features
80m
Integrated Power N-Channel MOSFET Switches
Accurate Current Sensing and Limiting
12ms Fault Delay to Latch-Off, No Thermal Dependency
2.5V to 5.5V Operating Range
Disabled Output Internally Pulled Low
Undervoltage Lockout
Controlled Turn-On Ramp Time
Channel Independent Fault Output Signals
Channel Independent Logic Level Enable High Inputs
(ISL6118H) or Enable Low Inputs (ISL6118L)
Pb-Free Package Options Available
Tape & Reel Packing with ‘-T’ Part Number Suffix
Applications
ACPI 3.3V AUX Control
Electronic Circuit Limiting and Breaker
Pinout
ISL6118 (SOIC)
TOP VIEW
Ordering Information
PART #
TEMP.
RANGE (°C)
PKG.
PKG.
DWG. #
ISL6118LIB
-40 to 85
8 Ld SOIC
M8.15
ISL6118LIBZA (Note)
-40 to 85
8 Ld SOIC (Pb-free)
M8.15
ISL6118HIB
-40 to 85
8 Ld SOIC
M8.15
ISL6118HIBZA (Note)
-40 to 85
8 Ld SOIC (Pb-free)
M8.15
ISL6118EVAL1
ISL6118 Evaluation Platform
ISL6AHPEVAL1
ACPI (HIP1011D and ISL6118H) Evaluation
Platform
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which is compatible with both SnPb and Pb-free
soldering operations. Intersil Pb-free products are MSL classified at
Pb-free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J Std-020B.
GND
VIN
ENABLE_1
ENABLE_2
1
2
3
4
8
7
6
5
FAULT_1
OUT_1
OUT_2
FAULT_2
Data Sheet
March 2004
相關PDF資料 |
PDF描述 |
|---|---|
| ISL16AHPEVAL1 | JT 100C 100#22M SKT RECP |
| ISL6118EVAL1 | Dual Power Supply Controller |
| ISL6118EVAL1-T | Dual Power Supply Controller |
| ISL6118LIB | Dual Power Supply Controller |
| ISL6118LIB-T | Dual Power Supply Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6118EVAL1 | 功能描述:EVALUATION PLATFORM FOR ISL6118 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6118EVAL1-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Power Supply Controller |
| ISL6118HIB | 功能描述:IC CTRLR DUAL PWR SUPPLY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6118HIB-T | 功能描述:IC CTRLR DUAL PWR SUPPLY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6118HIBZA | 功能描述:IC DUAL PWR SUPPLY CTRLR 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。