- 您現在的位置：買賣IC網 > PDF目錄360996 > ISO130PB Amplifier. Other PDF資料下載
參數資料
| 型號： | ISO130PB |
| 英文描述： | Amplifier. Other |
| 中文描述： | 放大器。其他 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 127K |
| 代理商： | ISO130PB |
9
ISO130
THEORY OF OPERATION
The ISO130 isolation amplifier (Figure 1) uses an input and
output section galvanically isolated by a high speed optical
barrier built into the plastic package. The input signal is
converted to a time averaged serial bit stream by use of a
sigma-delta analog-to-digital converter and then optically
transmitted digitally across the isolation barrier. The output
section receives the digital signal and converts it to an
analog voltage, which is then filtered to produce the final
output signal.
Internal amplifiers are chopper-stabilized to help maintain
device accuracy over time and temperature. The encoder
circuit eliminates the effects of pulse-width distortion of the
optically transmitted data by generating one pulse for every
edge of the converter data to be transmitted. This coding
scheme reduces the effects of the non-ideal characteristics of
the LED, such as non-linearity and drift over time and
temperature.
ISOLATION AND INSULATION SPECIFICATIONS
The performance of the isolation barrier of the ISO130 is
specified with three specifications, two of which require
high voltage testing. In accordance with UL1577, the barrier
integrity of each isolation amplifier is proof-tested by apply-
ing an insulation test voltage greater than or equal to
4500Vrms for one second. This is to guarantee the isolation
amplifier will survive a 3750V transient voltage. The barrier
leakage current test limit is 5
μ
A. Pins 1-4 are shorted
together and pins 5-8 are shorted together during the test.
This test is followed by the partial discharge isolation
voltage test as specified in the German VDE0884. This
method requires the measurement of small current pulses
(<5pico Colomb) while applying 960Vrms across every
ISO130 isolation barrier. This guarantees 600Vrms continu-
ous isolation (V
ISO
) voltage. No partial discharge may be
initiated to pass this test. This criterion confirms transient
overvoltage (1.6
x
600Vrms) protection without damage to
the ISO130.
This test method represents “state of the art” for nondestruc-
tive high voltage reliability testing. It is based on the effects
of nonuniform fields that exist in heterogeneous dielectric
material during barrier degradation. In the case of void non-
uniformities, electric field stress begins to ionize the void
region before bridging the entire high voltage barrier. The
transient conduction of charge during and after the ioniza-
tion can be detected externally as a burst of 0.01 to 0.1
μ
s
current pulses that repeat on each AC voltage cycle. The
minimum AC barrier voltage that initiates partial discharge
is defined as the “inception voltage”. Decreasing the barrier
voltage to a lower level is required before partial discharge
ceases and is defined as the “extinction voltage”.
FIGURE 1. Block Diagram of ISO130 Isolation Amplifier.
Decoder
and
D/A
Detector
CIrcuit
Filter
LED
Drive
Circuit
Σ
A/D
and
Encoder
Voltage
Regulator
Clk
Isolation
Barrier
Voltage
Regulator
Output
Input
FIGURE 2. Isolation Mode Rejection and Transient Immunity Test Circuit.
78L05
In
Out
9V
0.1μF
2
ISO130
3
4
+5V
8
5
7
OPA604
1k
1k
5.11k
330pF
6
0.1μF
+15V
–15V
330pF
5.11k
0.1μF
+
–
V
OUT
0.1μF
Pulse Generator
V
IM
V
OUT+
1
+
0.1μF
相關PDF資料 |
PDF描述 |
|---|---|
| ISO130U | Amplifier. Other |
| ISO130UB | Amplifier. Other |
| ISO150 | Dual, Isolated, Bi-Directional DIGITAL COUPLER |
| ISO150AP | Dual, Isolated, Bi-Directional DIGITAL COUPLER |
| ISO150AU | Dual, Isolated, Bi-Directional DIGITAL COUPLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISO130U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Amplifier. Other |
| ISO130UB | 制造商:BB 制造商全稱:BB 功能描述:High IMR, Low Cost ISOLATION AMPLIFIER |
| ISO15 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ISOLATED 3.3-V FULL AND HALF-DUPLEX RS-485 TRANSCEIVERS |
| ISO15_08 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ISOLATED 3.3-V FULL AND HALF-DUPLEX RS-485 TRANSCEIVERS |
| ISO150 | 制造商:BB 制造商全稱:BB 功能描述:Dual, Isolated, Bi-Directional DIGITAL COUPLER |
發布緊急采購，3分鐘左右您將得到回復。